Differentiate 1. Method of removal 2. Kind of work material 3. Type of cut EDM, USM, and ECM as to

Q: Question 1 A ramp is made by leaning a track against a few textbooks. A cart Is Set track and rolls…

A:

Q: 1-The graphitization of cast iron effected by ………………………..? 2-The hardness test…

A: The graphitization of cast iron effected by keeping the material in elevated temperatures for long…

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: I have two parts that need to be answered (Multiple Choice). If you can not answer both parts,…

A: In the left side view of the print, there is a horizontal, straight-line segment on the left side…

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

A:

Q: For 10-2 above, the last part of Step 6 and the final answer seems to be missing or cut off on my…

A:

Q: Don't use chatgpt will upvote

A: 1. Vertical Position EquationY(t)=V0​t−21​gt2V0​ is the initial speed of the ball,g is the…

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: Please walk me through finding how much force the women need to pull the force

A: Given data: Weight is W Need to determine the required force to pull the weight.

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: determine Vp, f, and Ø, and insert

A:

Q: a powerp u, a process design id wastes (MSW) per hour. In an industrial boiler, MSW is burned to…

A: To given thatH1=104.93Kj/kgH2=2675.53kJ/kgH3=2942.73kJ/kgH4=3324.63kJ/kg

Q: I need the answers to this part, I have submitted this question twice on this site and both times…

A: Sampling length – 5 Minimum material to be removed is specified -  1 Rough machine finish – 3…

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&T symbols used in the image:Datum symbols: A datum is a…

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with…

A: Given Data⇒ Load intensity for rectangular section : F=4 KNm Distance upon which load is…

Q: 3. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: This problem set deals with the problem of non-constant acceleration. Two researchers from Fly By…

A: Given: To find: Write all equations Construct least squares problem Construct system of normal…

Q: An air conditioning unit uses Freon (R-22) to adapt an office room at temperature 25 oC in the…

A: The data given in the problem is, Temperature at condenser, T1 = 48℃ Temperature at evaporator, T2…

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Q: Each bar chart should show the distribution of energy across the categories as well as the total…

A:

Q: I will rate you with “UPVOTE/LIKE” if you answer every question.   I will rate you with “DOWNVOTE/

A: Given Data : Definitions Moment Principle

Q: I need parts 3 and 4 answered pertaining to the print provided.  I asked this question previously on…

A: (3) In the empty space of revision A9 a general note 3.6 is added stated that the revised geometric…

Q: What is the distance between the points labeled A and B? Start a new drawing based on…

A: According to the given data Thickness of the wall=100mm We need to find Distance b/w A and B

Q: What is the equivalent resultant force and specify its location, measured from point 0. * FR= 13.5…

A:

Q: Hot water (specific heat of 4.18 Kj/kgK) at 66C is flowing through a metal pipe (6 m long, 2 cm ID,…

A: Given  Hot water is flowing through a metal pipe.  Specific heat of water = 4.18 Kj/KgK Temperature…

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: SEND THE ANSWER IN 10 MINUTES PLEASE Assume that you measure the diameter of sphere with a…

A: Assume that you measure the diameter of sphere with a micrometer caliper many times and obtain the…

Q: What is the unstretched length in DB? * O 1.572 m O 1.837 m O 1.769 m O 3.606 m

A:

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: Answer to question no. 1Yes, the print shows the detail drawing of a single part here. The drawing…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Q: 4. With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.