A flexible circular area is subjected to a uniformly distributed load of 150 kN/m². The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesq's solution.

A flexible circular area is subjected to a uniformly distributed load of 150 kN/m². The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesq's solution.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.12P: Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below...

See similar textbooks

Related questions

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface. Based on Boussinesq's…

A: Given data- Line load UDL=500 kN/mdepths-z1=2 mz2=4 mTo Find-Ratio of vertical stresses at 2 m and 4…

Q: A soil fails under an axial vertical stress of 100kN / (m ^ 2) in unconfined compression test. The…

Q: 85 kN/m2 25 kN/m2 Try solving the following problem: Practice Problem 1: (Repeat practice problem…

A: Given data σx = -45 KN/m2 σy = -85 KN/m2 τxy = τyx = -25 KN/m2 θ = 90° - 40° = 60° (plane AB make…

Q: Tpis) Refer to Figure 3.67, a flexible rectangular area is subjected to a uniformly distributed load…

A: Given Case 1 : r = 0 & z = 3 m and Case 2 : r = 2.2 m & z = 3 m Q = load = 225×6×3 =…

Q: Calculate the effective stress at point A for the following soil profile:

Q: Consider a circularly loaded flexible area acting on the ground surface. The radius of the circular…

A: z=10ft q=1000lb/ft2

Q: A uniformly distributed line load is acting on the ground surface. Based on the Boussinesq's theory,…

Q: Question 1 A 5-m depth of sand overlies a 6-m layer of clay, the water table being at the surface.…

Q: Given soil formation and the corresponding properties of soil in each layer. To consolidate the…

A: step 1-

Q: The stresses on a failure plane in a drained triaxial test on sand are as Follows: Normal Stress nf…

Q: The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2 What is…

A: The angle of intersection is given by:

Q: Problem 3.7 For the seepage situations shown in Figure, determine the effective normal stress on…

A: Solution1By considering pore water pressure::σ'=σ-uσ=20×2+3×9.81=69.43KPau=1+39.81=39.24σ'=30.2kpaBy…

Q: Given in figure is soil profile where the groundwater table is 4m below the ground surface,…

Q: A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: SITUATION. From the soil profile shown below, Ground surface Dry Sand Clay A e = 0.49 Gs=2.68 Ground…

Q: nother method of determining the capillary rise in a soil is to use Hazen's capillary formula. The m…

A: GIVEN DATA:-⇒Dense silt layer thickness= 3m⇒Clay layer = 5m⇒Bulk unit weight of soil = 26.5…

Q: A rectangular foundation 4 m x 6 m transmits stress of 300 kPa on the surface of a soil deposit, as…

A: r=4m z=5m

Q: Use Eq. (6.14) to determine the stress increase Δσ at z = 10 ft below the center of the area…

A: Solution; Calculate parameter m1 as follows: m1=LBHere,The width of the foundation =B=10 ftLength of…

Q: | A uniformly distributed line load of 500 kN/m is acting on the ground surface. Based on…

A: Given data: A uniformly distributed line load, q' = 500 kN/m

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface based on Boussinesq's…

A: Given data: A uniformly distributed line load of 500 kN/m. The ratio of vertical stress at a depth 2…

Q: Calculate the effective stress at A. Sand 25 m Water Table and- Gravel Unit Weight (y) = 20.72 kN/m…

A: Following is the given soil profile:

Q: 35 At the construction site, 3 m thick clay layer is followed by 4 m thick gravel layer which rest…

Q: A soil with a unit weight of 18 kN/m3 is loaded on the ground surface by a uniformly distributed…

Q: A flexible rectangular area is subjected to a uniformly distributed load of q 225 kN/m. Determine…

A: Given data in question Dimensions Semi circular Large square Small inside square Depth To find out…

Q: A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: A shallow foundation 25 x 18 m carries a uniform pressure of 175 k N / m 2 . Determine the vertical…

Q: a uniform p

Q: (b) Figure Q2 (b) shows the ring foundation to support a silo. Given R1 = 3 m while R2 = 6 m. The…

A: Given data: R1= 3 mR2=6 m Depth 7 m with a interval of 1m.

Q: A circular foundation 2m in diameter is shown in the figure below. A normally consolidated clay…

Q: The effective stress strength parameters of soil are c'= 10 kPa and p = 30°, then shear strength on…

A: Given data- Effective stress parameters-C'=10 kPaϕ=30ototal normal stress σ=300 kPapore water…

Q: show the variation beneath the edge of the loaded area.

A: Consider the following equation : σz=q1-11+r2232 Here r= 5ft Plot the variation of the vertical…

Q: Determine the internal friction angle of a cohesionless soil that has been tested under a normal…

A: Given: Cohesion = 0 Normal stress = 200 kN/m2 Shear stress = 100 kN/m2

Q: A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the…

Q: A rectangular concrete slab, 3 m x 4.5 m, rests on the surface of a soil mass. The load on the slab…

Q: Calculate the added vertical stress at points A and B as deep as Z = 8 m, under the rectangular load

Q: 3. A site is underlain by two soil layers over bedrock. The unit weights of the top (sand) layer are…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A layer of saturated clay 4m thick is overlain by sand 5m deep, the water table being 3m below the…

Q: Determine the vertical stress increase 6 m below point E.

Q: B q = Load per unit area

Q: The stress of soil (kN/m2) is influenced by the force and depth density and area unit weight and…

Q: Q1) Data obtained from a drained triaxle test are cell pressure o3 = 50 kN/ m? and deviator stress o…

Q: for a soil profile consists of a two- way drainage clay layer of 5 meters with W.T at N.G.S., total…

A: For any soil when it is subjected to external loading or surcharge loading it shows the long term…

Q: 5-9 Plot the distribution of vertical stress increase (Aoz) at a depth of 2 m below grouiu surface…

A: Given data Point load Depth To find Results given by two theories

Q: SITUATION: In accordance with Boussinesq theory, the vertical stress at a point below the center of…

Q: Determine the value of the effective stress at the depth of 5 m in the given soil element. The…

A: Given: Specific gravity, Gs = 2.7 Soil 1 (Up to depth of 2 m): Degree of saturation, S = 0.6 Water…

Q: A level ground surface exists in an area where soil in the underlying stratum has a wet unit weight…

A: Mohr's circle for stress combination The expression for major principal stress acting at a point is…

Q: The plan of a flexible rectangular loaded area is shown in Figure below. The uniformly distributed…

Q: EXAMPLE1. Plot the variation of total and effective vertical stresses, and pore water • Examples…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

H.Q 3
A flexible circular area is subjected to a uniformly distributed load of
150 kN/m2. The diameter of the load area is 2 m. Determine the stress
increase in a soil mass at points located 3 m below the loaded area at r
= 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesq's solution.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
ASAP
A uniform loading of 150kPa is applied at a 28 m Χ 28 m area. Please calculate the consolidation settlement of the clay layer used the middle of the clay layer to estimate the stress increment with the influence factor method). Cc = 0.4, Cs = 0.04, preconsolidation stress is 150 kPa and unit weight of water is 10 kN/m3. What is the settlement at the corner and center of the loading? What is the differential settlement between the corner and the center?
the results of a consolidated undrained test, in which o3 = 392 kN/m?, %3D on a normally consolidated clay are given next: Axial Strain, % Ao, kN/m2 Ud, kN/m? 0.5 156 99 0.75 196 120 1 226 132 1.3 235 147 2 250 161 3 245 170 4 240 173 4.5 235 175 Draw the kf line in a p' vs q' diagram. Also draw the stress path for the test in the diagram.
the angle of internal frictional of a cohesive soil which was tested using tria-axial shear apparatus is equal to 26.57. failure occurred when the shearing stress is 250 kPa and the normal stress is 480 kPa. a. determine the maximum principal stress at failure, in kPa. round off to two decimal b. deternmine the cohesion of the soil in kPa. round off to two decimal c. determine the deviator stress at failure in kPa.round off to two decimal
A soil element is loaded from state A to B. The stress values for the two states are A(p'=50 kPa, q=20 kPa), and B(p'=280 kPa, q=120 kPa). The bulk modulus of the soil is 1000 kPa, and its shear modulus is 1300 kPa. Work out the volumetric strain increment from the loading.
2- A three-axis compression test has been performed on the clay sample, which has been comprehensively and normally strengthened to a stress of 300 kPa and a specific volume of 200. The values of q and volumetric strain are measured at axial strain of 0, 2 and percent (rupture). The value of N is equal to 300 and Landa is equal to 0.2. Draw a diagram of all- round stress on the initial all-round stress in terms of slicing on the initial all-round stress:.
For the stressed soil element shown:a. Compute the major principal stressb. Compute the minor principal stressc. Compute the normal stress on plane DE
Mohr-Coulomb Criteria Q.15 The effective stress strength parameters of a soil are c = 10 kPa and p = 30, then shear 4 strength on a plane within the saturated soil mass at a point where total normal stress is 300 kPa and pore water pressure is 150 kPa, will be
in a drained triangle test on consolidated clay the stress and angle area as follows deviator stress is 20 lb/ in ^2 and friction angle is 21 degree calculate the effective confining pressure at failure
At failure, the major and minor principal stresses on a triaxial test are 200 kPa and 110 kPa respectively. If the porewater pressure at failure is 25 kPa... Q: What is the sine of the angle of shearing resistance of the soil? Round off your answer to two decimal places.