A fireworks show is choreographed to have two shells cross paths at a height of 177 feet and explode at an apex of 222 feet under normal weather conditions. If the shells have a launch angle 8 = 54° above the horizontal, determine the common launch speed vo for the shells, the separation distance d between the launch points A and B, and the time t from launch at which the shells explode. 45 177

A fireworks show is choreographed to have two shells cross paths at a height of 177 feet and explode at an apex of 222 feet under normal weather conditions. If the shells have a launch angle 8 = 54° above the horizontal, determine the common launch speed vo for the shells, the separation distance d between the launch points A and B, and the time t from launch at which the shells explode. 45 177

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the questions below, (Insert the numerical value only, do not use ,+, *, or /) The Relative error for your answer should be less than 0.01, which means if the answer was 50, then the error should not exceed 50*0.01= ±0.5! if the answer was 230, then the error should not exceed 230*0.01= +2 3! if the answer was 2.31467*10^ 3, then you should enter this value: 0.00231467, not this 0.0023 !!!! K2 K1 M1 fv1 M2 f(t) if M1=4, M2=3, fv1=7, K1=4, K2=6. Find the state equations for the translational mechanical system shown in Figure. [d/dt(r1) d/dt(v1) [(1.1) (1.2) (1.3) (1.4) rl (1)] (2.1) (2.2) (2.3) (2.4) (3.1) (3.2) (3.3) (3.4) [(4.1) (4.2) (4.3) (4.4)] vl * f(t)$$ $$ d/dt(r2) d/dt(v2) r2
Please provide more details for question b and c. thank you
LESSON: AUTODESK AUTOCAD Choose from the choices:
1A
Number 4
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
The attached answer was provided for the attached question. The equation uses the given temperature in celcius and the answer is also given in celcius. The temperature was used in the equation without converting from F and the answer was supposed to be in F. I am worried that even if I converted the answer to celcius that it would be correct because temperature was used in the equation using the incorrect unit.
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…
Essay format: Write 3 paragraph(3-5 sentences each)or more on what are the challenges in engineering in thermal engines and thermodynamics cycles and add a conclusion in your own words of 5 sentences. Use a scientific article and cite where needed and list the name and author of article below. No PLAGIARISM! Please allow someone to assist that is willing to take the time and answer correctly, if written properly I will upvote. IF YOU WILL NOT HELP OR ATLEAST READ AND ANSWER PROPERLY THEN I WILL DOWN VOTE. SO PLEASE ALLOW SOMEONE TO HELP THAT IS WILLING.
Need help answering these questions.
Read each sentence carefully, and then mark as True or False. * a) Cast iron has a carbon content between 1 % and 4 %. b) In the gray cast irons, C is precipitated as graphite flakes. c) In the white cast iron, Fe is precipitated as flakes. d) Cementite is a mixture of two phases, austenite and ledeburite (Fe3C). e) Pearlite is the eutectoid mixture containing 0.80 % C and is formed at 723°C on slow cooling