A cylindrical tank having a diameter of 5 m. and 8 m high is full of water. There is an orifice at the bottom of the tank having an area of 0.02 m?. A. Compute the coefficient of discharge C if it takes 746.21 sec to lower the water surface from 8 m to 3m. B. Compute the coefficient of discharge C if it takes 746.21 sec to lower the water surface from 8 m to 0m. C. Compute the coefficient of discharge C if it takes 746.21 sec to empty the tank.

A cylindrical tank having a diameter of 5 m. and 8 m high is full of water. There is an orifice at the bottom of the tank having an area of 0.02 m?. A. Compute the coefficient of discharge C if it takes 746.21 sec to lower the water surface from 8 m to 3m. B. Compute the coefficient of discharge C if it takes 746.21 sec to lower the water surface from 8 m to 0m. C. Compute the coefficient of discharge C if it takes 746.21 sec to empty the tank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 7: From reservoir A whose water surface elevation is 225 m. Water is pumped through a 350 mm pipe across a valley at a second reservoir B at a elevation of 240 m. During pump, the pressure is 570 kPa at a point C and at elevation of 195 m. Assume that the headloss in the pipe from reservoir A to point C is 30 times its velocity head and from point C to reservoir B is 50 times its velocity head 23. Compute the discharge in the pipeline in L/s 24. Compute the head added by the pump 25. Compute the horsepower exerted by the pump IVA E1225 m El 240 m El 195 m
1. Water is following steadily through a 50 m long section of a horizontal 5-cm diameter stainless steel pipe. The water temperature is 15°C and the flow rate is 9 L/s. Determine: a.) The pressure drop over the pipe length [kPa]. b.) The head loss [m]. c.) The pumping power needed to overcome the pressure drop (assume a pump efficiency of 67%) [kW]. 9 L/s 5 cm 50 m
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
A cylindrical tank 1m in diameter and 6m high contains 2m of water, 1.50m of oil (specific gravity = 0.8) and air under pressure of 20 KPa. If the 10cm diameter orifice located at the vertical side is 30 cm above the bottom of the tank, find the actual discharge at the orifice if C = 0.95. A) No Answer among the choices B) 79.11 L/s 59.95 L/s D) 54.40 L/s E) 73.45 L/s
Determine the flow (m³/s) in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 L/s.