A consulting firm is asked to perform a study of pipe flow. A fluid flows at velocity, V, through thepipe of diameter, D. An orifice plate containing a hole of diameter, d, is placed in the pipe (thismeans the pipe diameter is essentially reduced to d at this location). It is desired to study thepressure drop, AP, across the plate. Assume that AP = f(D, d, o, V). Determine a suitable set ofpi terms.

Answered: A consulting firm is asked to perform a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The four pipes below have steady flow of an incompressible, ideal fluid with density ps. The manometer fluid density is pm. Define AP = P2-P₁. Note the manometer reading Rm is called Ah in Figure 2.11 of Song (2018). Part A For each manometer, check the appropriate box in each of the three pairs of options. Rm (a) □ Pm Pr □ P₁ P₂ AP=Rm(Ym-Y) AP=Rm(Yr Ym) (b) □Pm Pr O P₁ P₂ OP₁ > P₂ AP=Rm(Ym-Y) AP=Rm(Yr Ym) Rin (c) □ Pm Pr □ P₁ P₂ DAP-Rm(Ym-Y) AP=Rm(Yr Ym) Rm (d) OPm Pr □ P₁ P₂ *2 O AP=Rm(Ym-Yt) □ AP=Rm(Yt-Ym) Part B For one of the manometers shown, derive the equation you checked for pressure drop AP. Be sure to state which manometer are you using for your derivation (a)-(d).
Q1) Mott recommends the following formula for the friction head loss hf, for flow through a pipe of length L and diameter D : where Q is the volume flow rate , A is the pipe cross-section area , and Ch is a dimensionless coefficient . Determine the dimensions of hf? hf = LG *0.551. A. Ch. Do.63)1.85
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine, (a) Discharge of oil (b) The pressure difference in N/m^2 between * entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98
Two concentric glass tubes immersed in water as shown in figure. The outer tube has diameter of (D = 5 mm) and the inner one has diameter of (d = 4 mm). With neglecting of tube wall thickness, find Ah. Ah D water
The velocity profile of water(density 1000 kg/m and viscosity of 0.001 N.S/m² ) in a pipe is u%=²(R² -r²) where R is radius of the pipe and r is any distance from the center of the pipe. %3D The roughness of the pipe is 0.03 mm. i. If the pipe is replaced by another pipe with higher roughness of 0.075 mm, Calculate the pressure drop in two-meter length of the pipe. ii. evaluate the pressure drop in two-meter. ii. Explain your answers (difference or similarity) in parts (i) and (ii).
Find flow velocity and flow rate in pipe a and b using Equivalent pipe length method and hazen williams formula
Someone can help me with this one please.
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
The discharge (Q)through a horizontal pipe is depend upon the pressure drop per unit length the diameter (D), and the dynamic viscosity (μ).Find the form of the equation using Dimensional Analysis theory.
ANS BOTH!
This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. What will be the gage pressure reading at A? correction: 3.75 mm should be 375 mm en Me Do not write the unit. You will only input the numerikal answer in the space provided. Unit of the Correct Answer. kPa Decimal Places required in the firal answer 3
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine,(a) Discharge of oil (b) The pressure difference in N/m”2 between entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98*

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS