A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-º/°C; v = 0.33] pipe has an outside diameter of. and a length of 5.3 m. The pipe supports a compressive load of 635 kN. After the temperature of th (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i mm AD = i mm Save for Later Atte

A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-º/°C; v = 0.33] pipe has an outside diameter of. and a length of 5.3 m. The pipe supports a compressive load of 635 kN. After the temperature of th (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i mm AD = i mm Save for Later Atte

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel pipe of length L= 3 ft, outside diameter d₂- 10 in., and inside diameter dy = 5.1 in. is compressed by an axial force P= 107 kips. The material has = Poisson's ratio v=0.30. Determine the increase in thickness.
Q2. Show that = Cr2(a - 0 + sin 0 cos 0 – tan a cos? 0) is a permissible Airy function for the tapered cantilever of uniform thickness, shown in Figure 2, and derive expressions for the corresponding stresses or, 0g and tre. Also, find the %3D value of the radial stress at 0-0° when a=30°. w/ unit length Figure 2
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
FN = 50
The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal and circumferential stress caused by an internal pressure of 125 psi (Ib/in²). 1. Drive the expressions for longitudinal and tangentional stresses? 2. Calculate the maximum longitudinal and circumferential stress caused by an internal pressure? Fw Fw Fp Fp XLV 1.5 ft |1= 1/8 in Fw Fw Fw Fw 0.75 ft LONGITUDINAL STRESS, ₁ TANGENTIAL STRESS , 2 ft 1.5ft ث إضافة ملف
PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10°/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa α = 17.3 x 10/°C
The state of stress at a point in a structural member is given by = 0x = Ax² + By², ay = Cy² + Dz², oz Ez² + Fx² Txy = Gy + Hz, Txz = Iz + Jx, Tyz = Kx + Ly where A, B,..., L are constants. Find expressions of the body forces to ensure the equi- librium. Units of the stresses are MPa.
A spherical tank of diameter 1.2 m and wall thickness 50 mm contains compressed air at a pressure of 17 MPa. What is the value of tensile stress? (Assume E = 210 GPa, v = 0.29)
Q4 / A thick cylinder of (200mm) external diameter and (100mm) internal diameter, the internal pressure of (90MPa) applied only, Determine:- 1- Stresses that developed on outer and inner surfaces of cylinder. 2- Strains at the outer and inner surface of cylinder. E-210GPa, v=0.3
Determine the outside diameter of a hollow steel rod that will carry a tensile load of 55,000 kg at a stress of 1,500 kg/cm² and the wall thickness is 10 mm. A. 8.17 cm B. 8.34 cm C. 12.67 cm D. 7.28 cm
Handwritten solution