Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a radius of 50 mm AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium A B T 0 R 90° U 3R D Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress e. Angle of twist

Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a radius of 50 mm AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium A B T 0 R 90° U 3R D Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress e. Angle of twist

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given is a thin-walled tube with the following data:Wall thickness- 3mmTorque is 900 N.mLength of the thin walled tube is 1.2 m.Use G=24 GPa for aluminium Determine the following:a. Enclosed Areab. Perimeter of the thin walled tubec. Shear flowd. Shear stresse. Angle of twist
Given is a thin-walled tube with the following data: Wall thickness- 3mm Torque is 900 N.m Length of the thin walled tube is 1.2 m. Use G=24 GPa for aluminium A R100.00 0₁₂ C 400.00 Unit: mm Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress e. Angle of twist E D R50.00 B
www.VII He is acheveu by the survey 15.17 A pipe in a spacecraft, made of AISI 310 stainless steel, is near the rocket engine, causing it to be subjected to temperatures as high as 950°C. The stress applied to the pipe in actual service is expected to be 10 MPa. (a) How long would you allow the pipe to be subjected to the given temperature and stress if a safety factor of 10 on life is required? (b) What safety factor on stress is achieved by the safety factor of 10 on life? Does the resulting safety factor on stress seem reasonable and adequate?
Element 1 Ук ** Answer in MPa. 2 cm Element 2 Assume the reaction forces at the origin were solved to be Rf = [325, 100, 0] N and = Rm [10, -2, 5] Nm. We will consider a hypothetical cut at the connection of the dolly to the axle. Z is positive out of the page. What is the value of normal stress in the x-direction Ox for element 2? Answer options: a) Ox < -300 b) -300 ≤ Ox < -100 c) -100 ≤ Ox < -200 d) 0 ≤ Ox < 100 e) 100 ≤ Ox < 300 f) 300 ≤ Ox
stress 0.02 0.018 0.016 0.014 0.012 0.01 0.008 0.006 0.004 0.002 0.05 0.1 0.15 0.2 0.25 0.3 0.35 Determine : 1- Stress, Stratn care 2. elastic Zone 3. yield sbresscoys 4- plastic Zone 5- UItimate Stress Cous 6- Elongation 7- propotionaL stress cops 8-fructurc stress coF)
Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
Emmii DH Tube Corrugated Tube DH P (mm) e (mm) 25 7 1.5 0.013 Find the equivalent diameter 11:06
Answer the questions below for the following system. Young's modulus and Poison's ratio can be taken as 200 GPa and 0.3, respectively. a) Calculate and determine the stress state for point H using undergraduate level solid mechanics knowledge? b) Determine the principal stress values at point H using undergraduate level solid mechanics knowledge? Top view of section where H is located Point H no 300 mm 120 mm C .H 540 mm A Diameter of the pipe d=36 mm P=900 N
M13.6 Principal stresses from rosette data scenes -200 µE 23 Eb = 200 με Ec 500 µE 30° 30° Ex (LE) a Ey (µE) Yxy (Lurad) The strain rosette shown was used to obtain normal strain data at a point on the free surface of a steel (E = 200 GPa; v = 0.32) plate. Op1 (MPa) Determine the normal strains, the shear strain, and the principal stresses in the x-y plane. Op2 (MPa) Try One 1st 2nd 3rd attempt enter
A closed thin walled cylindrical vessel has a diameter D of 780 mm, a wall thickness t of 3.5 mm and length L of 950 mm. It is subject to an internal pressure P of 50.0 MPa. Assuming that Youngs modulus is 200 GN/m² and Poisson's ratio is 0.3, calculate the change in length of the vessel due to the internal pressure. Give your answer in mm to 3 significant figures. 00 P D 00 $ de OL 4
I want to know how much heat the tube lost due to the material it is made of aluminum or steel. Even if it is a small difference in temperature. I want to know which material Conduct Heat the Best through this problem. material: Aluminum, steel ( the dimensions are the same for both) temperature touching cylinder: 65 Celcius temeprature inside cylinder 64.5 celsius room temperature 24 celcius Tube measurements outer radius r1 r1 = 4 in inner radius r2 r2 = 3 in outer circumference C1 C1 = 25.132741228718 in inner circumference C2 C2 = 18.849555921539 in height h = 8 in wall thickness t = 1 in
Q1-B // A steel bar has a square section of 10 mm side and a length of 60 mm, subjected to a tension force of 50 KN, as a result the bar has extended 2 mm; Calculate: 1-Yong modulus 2- The engineering stress 3- The engineering sustain 4- The true stress 5- The true strain 6- The percentage reduction in Area