A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 200 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% V₂ Ce = 0 ע m₂ mF K ¹0 RL%

A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 200 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% V₂ Ce = 0 ע m₂ mF K ¹0 RL%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
For a sinusoidal input of 40 V (p-p) to the given circuit, what is the minimum value of the output waveform? NOTE: use ideal diode 0.7 30 20 -5 -40 K
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode current
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816