A cantilever wood beam with a span of L = 3.8 m supports a linearly distributed load with maximum intensity of wo. The beam width is b = 200 mm, and the beam height is h = 170 mm. The allowable bending stress of the wood is 5.1 MPa. Calculate the magnitude of the maximum load wo that may be carried by the beam. Wo A B Answer: wo = i kN/m

A cantilever wood beam with a span of L = 3.8 m supports a linearly distributed load with maximum intensity of wo. The beam width is b = 200 mm, and the beam height is h = 170 mm. The allowable bending stress of the wood is 5.1 MPa. Calculate the magnitude of the maximum load wo that may be carried by the beam. Wo A B Answer: wo = i kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4
E5
4. A piece of wood contains a glued joint inclined at an angle as shown in the figure. If the dimension of the wood is found to be 120mm by 120mm and the working stresses are 20 MPa for the axial stress(in tension) of the wood, 8 MPa for the normal stress of the glue, and 12 MPa for the shear stress of the glue. If the angle theta is 50°, determine the largest allowable value for the axial force P. P
FE.Question 3.KK
A composite beam 225 mm wide x 300 mm deep x 4 m long is made by bolting two 100-mm- wide x 300-mm-deep timber planks to the sides of a 25 x 300-mm structural aluminium plate. The moduli of elasticity for the timber and aluminium are 8 GPa and 73 GPa, respectively. Determine the maximum tensile flexural stress in each of the materials if the composite beam is simply supported and carries a concentrated load 30 kN in the centre of the beam. 100 mm 25 mm 100 mm 11 300 mm
A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
Problem The composite bar system in Figure 4.8 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the rigid block. If the total applied load P=42000 lb, determine the stresses in the two bars. 6′ S TE FIGURE 1.48 Composite bar system for Problem 12. Steel bar } Rigid block -} Bronze bar E₂ = 30 x 10º psi A₂ = 1 in² E-15 x 10 psi Ag-4 in²
The rectangular wood beam is loaded as shown in the figure. 12 kN. 8 KN/m 150 m 250 mm 10m 2 m What is the bending stress in the beam 2 meters from point A? 7.68 MPa O 5.76 MPa O 10.24 MPa 4.48 MPa What is the bending stress 50 mm from the top of the beam 0.5 meters from point A? * 3.456 MPa 5.760 MPa 10.245 MPa 6.144 MPa What is the shear stress in the beam at point C? O0.48 MPa 0.80 MPa 0.64 MPa O0.32 MPa
In the figure below, find the value of uniform load w (kN/m) that can be applied on the composite beam if the maximum stresses in steel and timber are 48MPa and 3.2MPA, respectively. Est=195GPa,Etimber=13GPA 120mm W Steel 10mm Timber 300mm 2m 4m 2m 250mm Steel 10mm 120mm
Q.3.L
4. Steel and aluminum plates are used to reinforced 100 x 175 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 130MPA Steel = 210MPA Aluminum = 90 MPa Aluminum = 80 MPa Wood = 20 MPa Wood = 15 MPa 30 mm CTEEL WOOD ww.skl A LUMINUM 140 mm
4