Three proposed cross-section configurations for joining three boards are shown in Figure 1. Each board is bx3b (b = <50+sum of last two digits of your roll+last digit of your roll> mm). If the bending moment about the z-axis is 5000 N m, what is the maximum bending stress in each cross-section? Which cross-section is the most effective use of the material in bending? %3D 36

Three proposed cross-section configurations for joining three boards are shown in Figure 1. Each board is bx3b (b = <50+sum of last two digits of your roll+last digit of your roll> mm). If the bending moment about the z-axis is 5000 N m, what is the maximum bending stress in each cross-section? Which cross-section is the most effective use of the material in bending? %3D 36

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the total deformation of the bars B1, B2 and Bz in mm. Determine the axial load acting on bar B; in kN. Determine the axial stress of bar B1 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN A) 2.5 (в) 1.79 0.54 D 3.75 (E) 4.83 А) 35 В) 20 D 5 10 A) 218.75 (B) 125 62.5 D 31.25
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
A steel rod with a cross sectional area of 120 (mm) ^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? a=11.7x [10] ^(-6)/°C and E = 200GPA. See figure 06. * Figure 06 120 MPa 130 MPa 140 MPa 150 MPa
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
A steel rod with a cross sectional area of 120 [mm] ^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? a=11.7x (10] ^(-6)/°C and E = 200GPA. See figure 06. * Figure 06 L Ti