A cantilever beam QT having rectangular cross sections with varying width h, and varying height b, is subjected to a uniform load of intensity q (see figure). hx hy br brz how should the height h, vary as a L If the width varies linearly with z according to the equation b, function of æ in order to have a fully stressed beam? (Express h, in terms of the height hr at the fixed end of the beam.)

A cantilever beam QT having rectangular cross sections with varying width h, and varying height b, is subjected to a uniform load of intensity q (see figure). hx hy br brz how should the height h, vary as a L If the width varies linearly with z according to the equation b, function of æ in order to have a fully stressed beam? (Express h, in terms of the height hr at the fixed end of the beam.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A beam cross section is shown. If the beam is subjected to a moment of 400N.m, the maximum bending stress will be? I, = 200 mm 4 8 mm 4 mm O a. 16GPA О Б. 10GPa 12GPA O d. 8GPA
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
A rectangular cantiliver wooden beam is applied by point load of 400in at free end Determine cross section area and second moment of inertia about bending axis and Draw internal effects shear and bending diagram Determine direct and shear stress at A on cross section of a-a .sketch state of stress
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of w, if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method. Prepare A 1m B Wo 3m 2m 30 230 m 10 10 10 (dimensions in mm) 150
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
150 mm 6 mm B 100 mm. i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 12 KN q = 4.8 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that Ew sign convention.) MPa maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel B 900 1m = 11 GPa and Es 200 GPa. (Enter your answers in MPa. Use the deformation =
8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of 200KN. If the length of the bar is 2m and E=200GPA, the elongation of the bar well be
3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional area of each bar so the bars fail at the same time with the load is P = 4 kips. Use a factor of safety of 1.8. 3 ft 4 ft P B σ (ksi) 25 20- 15 10- 5H 0 0 tension. compression 0.20 0.40 0.60 0.80 e (in./in.)