1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m

1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the cantilever has a partially hollow circular cross section. If the admissible normal stress is 140 MPa, determine the maximum value of Wo (distributed load intensity) that the beam can support. express your answer in KN / m
Help me friend
L. Mains A beam ABCDE is 5 m/in length and loaded as shown in Figure Q3. Draw the S.F. and B.M. diagrams for the beam, indicating all major values. Find also the value of the maximum bending stress if the beam section is rectangular 30 mm width by 60 mm depth. 3 kN 10 kNm 1 m B 1m 3 kN/m 640044 Stergat 1 m Figure Q2: Beam Loading 2 m SE
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
show step by step solution
Given: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The thickness of the plates is 25 mm and width of plate is 150 mm. find (a) the shear stress on the rivets (b) the bearing stress between a plate and a rivet; (c) the minimum average tensile stress in each plate. ft T T
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm?. B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. -50 mt 100 mm 400 50m Note : Take the value the 't' as equal to the last two digits of your student id. If the last wo digits are zero then takes T=10mm ww 00T
Determine the value of maximum principal stress
Higdon
Advanced