A butt joint with a double strap connects two axially loaded structural members as shown below. Determine the magnitude of the average shear stress in each bolt and in each nail if F = 825 lbf, dbolt = 0.25 in, and d-nail = 0.165 in. You may assume each bolt/nail passes through all members. The bolts are shown on the left side of the plate, and the nails are shown on the right side of the plate. F |TB₁avg| = |TN,avg| = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) ksi ksi ? F

A butt joint with a double strap connects two axially loaded structural members as shown below. Determine the magnitude of the average shear stress in each bolt and in each nail if F = 825 lbf, dbolt = 0.25 in, and d-nail = 0.165 in. You may assume each bolt/nail passes through all members. The bolts are shown on the left side of the plate, and the nails are shown on the right side of the plate. F |TB₁avg| = |TN,avg| = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) ksi ksi ? F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ENERAL INSTRUCTIONS: Write your complete solutions legibly on clean sheets of paper. I. Solve the following problems, complete with free body diagrams, clear solutions, and complete final answers. 100 kN 50 kN 1 2 |d1 — 30 тm d2 = 50 mm 1. 100 kN 0.9 m 1.2 m Rods 1 and 2 are welded together and are subjected to the shown loads. Given the measurements shown, determine the average normal stress internally experienced by rods 1 and 2, and specify whether these stresses are tensile or compressive.
Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: 1.0 in. -3 in--4 in. F1.0 in. A (in.?) a (J°F) E (psi) Aluminum cylinder 2.00 12.8 x 10-6 10 x 106 Bronze cylinder 3.00 10.5 x 10-6 12 x 10 Aluminum Bronze Each steel bolt 0.75 6.5 x 10-6 29 x 10 Q2/ The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250 mm?. If the temperature is increased by 80°C, determine the force P that will cause the bar at C to be stress-free. Use E = 200 GPa and a=12.8*10PC 3 m 0.8 m 0.6 m Ce D P
NEED ANSWER ASAP THANK YOU !! A joint is made by gluing two plywood gussets of thickness t = 0.78 in to wood boards. Determine the shear stress for the glue (in psi) if the dimension b = 17.51 in and the applied force is P = 9857 lb. Round off the final answer to three decimal places.
The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear stress in the bolts must be limited to 200 MPa, determine the minimum bolt diameter that may be used in the connection. 15.3 mm 13.5 mm 21.7 mm 25.2 mm 23.8 mm
AB çubuğunun çapı 17 mm ve BC çubuğunun çapı 25,5 mm'dir. Malzemenin emniyetli gerilmesi 170 MPa ve F=P olduğuna göre uygulanabilir en büyük P kuvveti kaçtır? The diameter of the AB bar is 17mm and the diameter of the BC bar is 25.5 mm. Since the safe stress of the material is 170MPa and F = P, What is the maximum applicable Force P?
Attempt Histor Current Attempt in Progress The five-bolt connection shown must support an applied load of P- 500 kN. If the average shear stress in the bolts must be limited to 270 MPa, determine the minimum bolt diameter that may be used in the connection. 27.8 mm O 13.5 mm 18.1 mm O 21.7 mm O 23.1 mm
5 Puan 800 N 45mm 800 N 9. The lapbelt assembly is to be subjected to a force of 800 N. Determine the required radius of the pin if the allowable tensile stress for the material is 20 MPa, allowable shear stress of glue is 15 MPa and allowable shear stress for the pin is 30 MPa. OA178 mm OB14.12 mm O D12.05 mm EE (Apolication/PubliclOnlineExam?examid=4718#
3. Determine the maximum average shear stress developed in each -in diameter bolt for the system shown below. 10 kip 5 kip 5 kip
Question 5 of 5 View Policies Current Attempt in Progress For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips. O 27.2 ksi O 37.5 ksi O 25.8 ksi O 21.9 ksi O 35.3 ksi
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 68 kips. O 18.9 ksi O 30.8 ksi O 36.5 ksi O 33.1 ksi O 22.7 ksi
The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.500 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod. | T Rod (1) Fixed plate Tube (2) B End plate D2 Answer: Tmax Ib-in.