Determine the tension in each cablenecessary for equilibrium of the masslesspipe supporting 800 N/m uniform load overa distance of 3 m if the support at A is ball-and-socket. Note that the structure issymmetrical about the x-z plane.X1.5 m800 N/m3 mB1 m1.5 m-1.5m1mZ1.5 m3 m

Uniform load applied on pipe:Total length of the uniform load:And structure is symmetric about XZ…

Answered: Determine the tension in each cable…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
The 428-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4202 N, Q = 3387 N, T = 40694 Nm, x = 1.14 m, y = 1.53 m, and z = 1.46 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.
Determine the force in the cable OC and the elongation of the spring OA, OB necessary to support a box of mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm. All calculation using equilibrium of particles equation and must be in Newton (N) and with FBD
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 1000 lb is applied to the tire at point C at an angle of 0 = 17° as shown. Assume the connection of the wheel to member AB is rigid. 1 h₁ K: LOFF 0 W₁ h₂ h3 h4 h5 B W₁₂ AXHIMAL W4 hs: h₂ cc i❀O BY NC SA 2013 Michael Swanbom W3 - W₁ Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value h₁ 6.6 in W1 7.5 in 16.6 in W2 4.6 in 14.6 in W3 8.3 in 10.2 in W4 6.2 in 5.2 in W5 9.7 in
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
2. Auniform bar 3.00 m long is held by ropes at the ends making angle 60.0° and 30.0°, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0° rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.) 3.00m T2 7 0.500m 60.0 B 200 N
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
The structure consists of a spring CD and a solid member ABC with a slot at B. The peg at B fits loosely into the slot at B and can hence be interpreted as a smooth support. The unstretched length of the spring is 80 mm. 50 mm 150 mm 50 mm A D C B k = 600 N/m 1.1 Draw separate free-body diagrams of member ABC and the spring CD. 1.2 Comment on the existence of two-force members and three-force members in this system. 1.3 Determine the reactions at A and B on the member ABC
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.
The following figure shows a hollow piston of weight W=50 N and diameter D=3d occupies the position initial displayed. The lateral tube has a diameter d₁=d/2. Find the descent of the piston for the equilibrium position. (b=12 cm, d=8 cm, y=104 N/m³). TBL Agua D d₁
A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
है A ★F B The structure shown above is in static equilibrium. The structure is made of square segments 1.5m on each side. Support A is a pin joint and support B is on rollers. An external force F=150.0 N is applied to the structure. What is the reaction force at B?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS