Q3: For the assembly shown in Fig. Q3. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Steel Bronze Aluminum B C A D P ЗР 4P | 1m 2m 1.5m A= 480 mm? A= 650 mm? A= 320 mm? E= 200 GPa E= 83 GPa E= 70 GPa Fig. Q3

Q3: For the assembly shown in Fig. Q3. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Steel Bronze Aluminum B C A D P ЗР 4P | 1m 2m 1.5m A= 480 mm? A= 650 mm? A= 320 mm? E= 200 GPa E= 83 GPa E= 70 GPa Fig. Q3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a laboratory test of a beam loaded by end couples, the fiber at layer -3 AB as shown are found to increase 40 x 10mm while those at CD decrease 70 x 10 mm in the 250-mm-gage length. Using E= 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. -3 Given: a 60 mm, b 120 mm, and C 80 mm. gage length a mm A 8. b mm D. c mm
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is oal = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? E=73GPA Bronze A=1500mm2 E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
E 0.4m D 10KN 0.8m 0.4m В 5KN 0.6m Al 20KN A=800 mm? A=1,200 mm?
simple strain with fbd
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
#4 will upvote to anyone who will answer
At a certain point in a structural member, the value of ox = -45 N/mm², ay = 75 N/mm² and t = 45 N/mm2. The principal stresses will be
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
Which of the following parameter represents principal stresses: T_a none of the available option O_X O_y 0_a
Question 4a pls
What is another term for bend? (A) flex B compress fracture D) twist E stretch