A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲfb. 208 µfc. 440 fd. 104 nf

A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲfb. 208 µfc. 440 fd. 104 nf

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: Question 4 An inductor wound with an insulated conductor was first energized using a DC power supply…

A: Asked to calculate the,(a) Impedance, Resistance and Inductance of the coil.(b) Power and power…

Q: An inductive load with impedance Z is connected to a single-phase 50Hz, 230V AC supply as shown in…

A: Supply voltage V = 230 volts,Frequency f = 50 Hz,Load power P = 7.5 kwatts.Load power factor = 0.65…

Q: Consider the diode circuit shown in Fig. Q6. Assume VDO = 0.7 V and the diode breakdown voltage is…

A: Since you have posted the questions with multiple support. So we are supposed to answer 3 subpart.In…

Q: Find the decimal equivalent of the following binary numbers expressed in the 2's complement format:…

A: Given data:Required information:

Q: A star connected alternator supplies a delta connected load. The impedance of the load branch is (8…

A: Given data:Required information:

Q: Q1/ Find Laplace Transformation for: 2 1. f(t) = t ²+ sin yt +3² t e 2- f(t) = Sin²t

Q: Consider the circuit in figure 1. a: Find Thevenin equivalent circuit with the respect to terminals…

A: Given:A circuit, we need to find:a) Thevenin equivalent circuit with respect to terminals a-b. b)…

Q: EXAMPLE 3-2 A 400-watt (400-W) carrier is modulated to a depth of 75 percent. Calculate the total…

A: Given data:Required information:

Q: 6.9 Calculate the radiation resistance of a X/16 aerial. Deter- mine its radiated power when the…

Q: Consider the circuit shown below. Assume that the current in the independent current source is given…

A: In the given R-L circuit, the current source expression isis(t)=2[u(t−0.5)−u(t−1)].To determine: the…

Q: a) For the following transfer function: H(s) = 100(s + 1) (s + 10) (s + 100) 1. Draw the Bode…

A: Given:To find:1) Plot the Bode diagram.2) Determine the gain margin and phase margin

Q: isnt Transformer ration V1 / V2 i see the opposite is here V2 / V1

A: Asked to explain the previously solved answer the transformer ratio.

Q: A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is…

A: Given:A BJT circuit, with current amplification factor ,Input Base current .Biasing voltage being…

Q: Fourier Transform -j2tux F(w= fa). e حفظ .dx B f(x) Consider the function shown above. Find it's…

Q: Determine the h parameters for the circuit in Fig. 19.24. 3Ω ww 292 Figure 19.24 592

A: The given circuit isWe need to determine the h-parameters for the circuit.

Q: Illustrate a single phase transformer and describe how it works? -why is voltage stepped up for…

A: Single-Phase Transformer:A single-phase transformer consists of two coils of wire wound around a…

Q: My teacher said that the equation v(t) for Vcap (in image) will be V = -1/C integral of i(t) +…

A: The capacitor's voltage:V=−1C∫i(t)dt+v(initial)v(initial)=+20V

Q: Write down the factors which affect the surface wave communication. Explain the major…

A: The question is asking about the factors that influence surface wave communication and the main…

Q: CHAPTER T In an electrostatic generator, if the negative surface charge density (10-c\m²), the width…

A: A basic characteristic of matter is electric charge. Charges come in two varieties: positive and…

Q: With switch SW1 closed and switch SW2 open, complete the following using the values from the table:…

A: The circuit is given asAccording to the question, when SW1 will be closed and SW2 will be open, the…

Q: Q4: The propagation of sky waves above the spherical earth represented by the Figure Imaginary…

A: To prove:The incidence angle at point P is:θ=sin−1(roro+h)

Q: 4. Using the circuit below, compute the individual values of the voltage and the current using…

A: In the given questions we need to calculate the voltage and current through each resistor.

Q: I need the see the actual MATLAB code for the Find the breakaway point on the real axis and the…

A: It is asked to write the MATLAB code for the root locus. Also we need to find the breakaway point on…

Q: A loaded Zener regulator shown in figure has: Vzv 6.3 + IZTMA IZK MA IZMmA Zz, 40 3 65 8 (a)…

A: Given data :Given circuit,Asked to determine,The minimum permissible load resistanceThe maximum…

Q: a) Given m(t)= sin 4000nt, the frequency deviation constant equals 400,000π radians/sec/volt and the…

Q: . What do you mean by aperture antenna? Explain the construction, working principle and the feeding…

A: An aperture antenna is a type of antenna where the size of the antenna is significantly larger than…

Q: Find mesh currents I1, I2 and I3

A: In this question, we need to determine the mesh currents . we solve this problem using the mesh…

Q: = ▸ A 100-KVA, 2500/125-V, 50–Hz, step-down transformer has the following parameters: R₁ = 1.5Ω, Χ,…

A: Given information,Rated output kVA.Induced EMF ratio Volts.So turns ratio is .Supply frequency…

Q: 3. In the network of Figure (2), use nodal analysis to determine : (a) The voltage at nodes B and C;…

A: Given Data:A DC resistive circuit of,To Find:The voltages at nodes B and C.The current The power

Q: 1.14 Calculate the voltages V1, V2 and V3 in the following arrangements. 9V OV (a) 50 Q V₁ 100Q 12V…

Q: With switch SW1 and SW2 both closed, complete the following using the values from the table:i.…

A: The circuit will be with both switch in close positionhere

Q: Calculate and draw the Discrete-Time Fourier Series of the following signal с x[n] TTTT -1-1

A: From the given discrete time signal we can see that:N=3For one interval:x[n]=[1,−1,−1]Now, from the…

Q: Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly…

A: 1- The current drawn by the armature of a D.C. motor is directly proportional to the torque. This is…

Q: please do as manual calculation

A: The objective of the question is to explain the construction technique of an Infinite Impulse…

Q: a) A signal has the amplitude spectrum shown. Sketch the signal in the time-domain. Amplitude -4 2 0

A: According to questions, we need to find the signal in time domain.

Q: Explain the construction, working principle and design of log-periodic antenna with necessary…

A: It is a multi-element antenna that offers good directivity over a wide range of frequency of…

Q: Q₁: A 4-pole, 460 V, 60 Hz, 3-phase induction motor star connected has the following circuit model…

A: As we have given :Asked to find the,Input current, Gross torque and efficiency.Maximum gross power…

Q: 4. Disconnect the DC power supply, and then measured the equivalent resistance by using the AVO…

A: Here, I write step-by-step how to measure the equivalent resistance using AVO meter:Safety…

Q: As shown in Figure 1, Find the output Voltage if Vin = 2.09 sin (2aft). Where f= 50 Hz, C= 1.369 µF…

Q: root locus

Q: Explain and draw a moving iron instrument. Show with a sketch how to measure voltage, current, and…

A: Moving-iron instruments are generally used to measure alternating voltages and currents. In…

Q: discrete time x[n] signal x[n] = 3δ[n + 1] + (n − 3)(u[n] − u[n − 2]) It is defined as ¸.…

A: A discrete signal is a type of signal that is defined and exists only at distinct points in time.…

Q: 4. Find the branch current analy R₁ loon E," IS V E R₁220 E₁20V 41. R: 580 -25

A: we have to findcurrent I1 and I2

Q: Series and parallel circuits are made from the same components as follows. A coil of resistance 300…

A: Since you have posted the questions with multiple subpart. So we are supposed to answer 3,subpart.…

Q: (1) In the circuit below, the two meters are digital multimeters (DMMs), with one set to the ammeter…

Q: C4 C(µF) C₁=5.0 C₂=7.0 C3=9.0 C4-6.0 Coq= Q (C) VV) W(J)

Q: dow does the use of multiple frequencies in FSK differ from the use of multiple amplitudes in ASK?…

A: "Since you have posted a question with multiple questions, we will provide the solution only to the…

Q: a) Draw the I-V characteristics curve of a typical p-n junction diode with clear indications of the…

Q: Consider the circuit below. The capacitor has a capacitance of 16 mF and starts out uncharged. The…

A: In the given questions we need to calculate the current flow through the battery and charge of…

Q: Use Nodal analysis to find the voltage Vp which is the voltage drop on 50 2 resistance. 20A 50 52 TV…

Question

A bridge full - wave rectifier with a capacitor - input filter provides a dc
output voltage of 14.5 V to a 330 ohm load. Determine the value of
filter capacitor if it connected to input voltage of 12 V rms, 50 Hz.
Question 7Answer a. 220 ɲf b. 208 ɲfc. 440 fd. 104 nf

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: We need to determine capacitor value of a bridge full wave rectifier

VIEW

Step 2: determining capacitor value of a bridge full wave rectifier

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Note: Answer All question 1: A) For a single-phase half-wave uncontrolled rectifier with (RL) load, find the rms value of the output voltage (V) and form factor (FF%) with supply voltage: v,(t) = 10 sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms. The conduction angle B = 220°. %3D
5- The frequency of the output voltage obtained from three-phase Wye/Delta connected rectifier is :* 6 times the rated source frequency. 3 times the rated source frequency 2 times the rated source frequency
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is: Square quasi-square six- step