5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is:

5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5- What is the advantage of the Zener diode ?
Q3) For the circuit shown in figure (2), assume the diode is ideal, answer the following: 1) Draw the output voltage then find the de output voltage. 2) If a capacitor 100uF is connected across RL load, Draw the output voltage then find de output voltage and Ripple Factor. 18:1 Vin 220V SOHz
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
Find the applied voltage on a forward biased diode if the current is 1mA and reverse saturation current is 10-10. Temperature is 25°C and takes ideality factor as 1.5.
Maximum voltage applied at single phase full wave rectifier diode is 440 Volt. load is resistive find value of average output voltage and rms output voltage.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=4 V and V2=10 V. R www DZ D1 Vin Vout vi V2 Maximum voltage of output waveform Minimum voltage of output waveform
!
H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr frequency = 5 kHz. 150usec and the source voltage V₁ = 200V at Calculate the average output voltage. EP
Draw the circuit diagram of a simple negative clamper with input and output wave forms for an input peak to peak voltage of Vpp= 12 V (Assume Germanium diode is used).
N H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150usec and the source voltage Vs = 200V at frequency = 5 kHz. Calculate the average output voltage. IC L.C. the HoNo locor
In a single phase half wave controlled rectifier with inductive load without freewheeling diode, the output voltage is zero during the wt=t to 2rt. Select one: O True O False
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate