Q-1 The beain ABC, Fig. 1, is fixed at A and roller supported at B. Determine the reaction components using the method of consistent deformations and draw the shear force and bending moment diagrams. (constant EI). -2-30x4 2 m 60 KN N 2 m 30 kN Jc 4 Fig.1

Q-1 The beain ABC, Fig. 1, is fixed at A and roller supported at B. Determine the reaction components using the method of consistent deformations and draw the shear force and bending moment diagrams. (constant EI). -2-30x4 2 m 60 KN N 2 m 30 kN Jc 4 Fig.1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The aluminium (G= 27.1 GPa) hollow thin walled torsion member has shown dimensions in Fig. 2. Its length is 3 m. If the member is subjected to a torque of 11 kN-m, determine the maximum shear stress and angle of twist. 120 mm b -200 mm 5 mm -5 mm, 5 mm Fig. 2 80 mm 5 mm 5 mm
Prob. 2.9-10. At room temperature (70°F) and with no axial load (P = 0) the extensional strain of the prismatic bar (Fig. P2.9-10) in the axial direction is zero, that is, € = 0. Subsequently, the bar is heated to 120°F and a tensile load P is applied. The material properties for the bar are: E = 10 × 10³ ksi and a = 13 x 10-6/F, and the cross-sectional area of the bar is 1.8 in². For the latter load-temperature condi- tion, the extensional strain is found to be €x = 900 × 10 6. (a) Determine the value of the axial tensile load P. (b) De- termine the normal stress and the shear stress on the oblique plane NN'. (Note: The total strain is the sum of strain asso- ciated with normal stress o (Eq. 2.14) and the strain due to change of temperature AT (Eq. 2.8).) in. P Gage measures extensional strain Ex N N' 25° P2.9-10 X
Q-2 Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.2. (EI is constant). 20 KN 10 KN B 2 m D et 2 m Fig.2
strain free, before the lantern is hung. When the lantern is hung, it causes a 50-mm sag in the wire. Determine the Prob. 2.3-6. Determine an expression for the extensional strain e(x) at cross section x (0sxsL) of the hanging con- ical frustum in Prob. 2.2-4, and (b) determine an expression for the total elongation, e, of this hanging conical frustum in Prob. 2.2-4. The conical-frustum rod is made of material for which o = Ee, with E= const. Prob. 2.3-7. For small loads, P, the rotation of "rigid" beam AF in Fig. P2.3-7 is controlled by the stretching of rod AB. For larger loads, the beam comes into contact with the top of col- umn DE, and further resistance to rotation is shared by the rod and the column. Assume (and later show that this is a valid as- sumption) that the angle 0 through which beam AF rotates is small enough that points on the beam essentially move verti- cally, even though they actually move on circular paths about the fixed pin at C. (a) A load P is applied at end F…
Q1: Due to the applied loading, the element at point A on the solid shaft in Fig.a is subjected to the state of stresses shown in Fig. b. Determine the principal stresses and maximum shear stresses acting at this point. Draw the element at each state of stresses. P Fig. a T 45 MPa <-30 MPa Fig. b 10 MPA
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
PLZ STEP BY STEP MORE SPACIFICATION
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B 20-mm diameter 60-mm diameter 1. Determine the deformation at segment AB in millimeter if P = 58 kN and Q = 0.
Solve using Method of Consistent Deformation
Q1: A torque T= 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa, Determine: (a) maximum shearing stress in the in the steel core (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A.
B) The free ends of two cantilever beams each of length L and flexural rigidity El are joined together with a spring as shown in Fig. (6). The stiffness of the spring is K = Using the method of consistent deformations, determine the force in the spring due to a concentrated load W acting at center of the lower cantilever. www
Determine the distribution of the shear stress over the cross section of the beam shown in Fig.a