A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 9 ksi. Given: ly=/₂=11.3 in 4 A=4.75 in² kmin = 0.983 in. Z 0.5 in. 1.43 in. с B ← 0.5 in. 5 in. 1.43 in. Y The largest permissible value of the moment Mo is 5 in. kip-in.

A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 9 ksi. Given: ly=/₂=11.3 in 4 A=4.75 in² kmin = 0.983 in. Z 0.5 in. 1.43 in. с B ← 0.5 in. 5 in. 1.43 in. Y The largest permissible value of the moment Mo is 5 in. kip-in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d, of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d; of the tube is equal to T = 1000 lb-in. 800 lb-in. T = T3 = 500 Ib-in. 500 lb-in. T = T5 = 800 1b-in. B C E dz = 1.0 in. O 0.697 in O 0.908 in O 0.788 in O 0.618 in
T·r T (from torsion) = Tr4 J ="- (Solid rod) F Onormal = A o (from bending) M•y - (Solid rod) The solid rod shown in the figure below has diameter of 1.25 in. If it is subjected to the force of 60 lb, determine the state of stress at point A using the principle of superposition. Neglect the weight of the rod, and the stress due to the I %3D I 4 transverse shear force. 60 lb k-10 in.- 15 in. Front View -20 in. В
Question 3 3.1 The short column in Figure 3 has a rectangle cross-section 80 mm x 50 mm. If the maximum compressive stress in the column is not to exceed 115 MPa, determine the magnitude of the greatest allowable vertical load P which can be carried. 30 mm 80 mm Fig. 1
The structure shown below consists of a brass core inserted into a steel tube of cross sectionsquare. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in thebar. E (brass) = 100 GPa, E (steel) = 200 GPa.
The couple M acts in a vertical plane and is applied to a beam as shown. Determine the stress at point A. M = 1.5 kNm 40 mm 0 = 30° 10 mm | 40 mm 10 mm - -70 mm→ 10 mm
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam measured from the bottom of the beam. b. Determine the centroidal moment of inertia. c. Determine the largest value of P if the allowable normal stress in tension is 80 MPa and 140 MPa in compression. 96 mm 12 mm T 12 mm 48 mm 0.25 m 0.5 m 0.15 m
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and = 11.7 um Neglect bending of the beam. m°C A=640mm2 A=320mm2 A 1.2 m 0.8 m 1.2m 54KN What is the stress of rod C if there is no change in temperature in MPa?
The State of stress at a point is shown with respect to the x-y axis. Determine the equivalent state of stress with respect to the x'-y' axis. Display the results on a sketch of an element aligned with the x'-y' axis. 8KSI 8KSI TOKSI Y' V Y X' 60° X 8KSI 10 KSI 8 KSI
An element in pure shear is subjected to stresses Tgy = 3,900 psi, as shown in the figure. Consider only the in-plane stresses (the stresses in the xy plane). 4 Txy Using Mohr's circle, determine: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see the figure) (Round your answers to nearest whole). psi psi psi Oz1 = Tzlyl Oyl %3D (b) The principal stresses. (Round your answers to nearest whole) Op1 %3D 01 = psi 02 = psi 3,
The circular shaft AB consists of a 19 mm diameter solid steel cylinder in which a 5 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 59 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. L₁ L₂ C 150 Nm B
1. A polyethylene bar (E = 1.4 GPa and v = 0.4) having di = 70 mm is placed inside a rigid steel tube having an inner diameter d2 = 70.2 mm. The polyethylene bar is then compressed by an axial load P. (a) At what value of P will the space between the polyethylene bar and the steel tube be closed? (b) If the compressive force P = 50 kN, determine the normal stress on the cylindrical surface of the bar, axial strain and the change in volume in the bar. Steel tube. 7p Ip Polyethylene- bar