A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. www Numm B A d2 5.5 m 4m 3.5 m 2m F Z m C Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d3 d₁ d5 G Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C is a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. kN kN kN

A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. www Numm B A d2 5.5 m 4m 3.5 m 2m F Z m C Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d3 d₁ d5 G Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C is a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. kN kN kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The linkage is made using two A992 steel rods, each having a circular cross section. If each rod has a diameter of 0.85 in. (Figure 1) Figure 1 12 ft of 1 P 45° -30° с Determine the largest load it can support without causing any rod to buckle. Assume that the rods are pin connected at their ends. Express your answer to three significant figures and include the appropriate units. μÃ Pmax = Value Submit Units My Answers Give Up ?
Problem 4.135 Replace the force system by a wrench. Suppose that F₁ = 300 N and F2 200 N. (Figure 1) Figure 1 ▼ of 1 F₁ x 2 m Z 0. 400 N 3 m 0.5 m F₂ Part A Determine the magnitude of the force of the wrench. Express your answer to three significant figures and include the appropriate units. F = Submit Part B M = Submit Part C I, z = μA Value Determine the couple moment of the wrench. Express your answer to three significant figures and include the appropriate units. Enter positive value if the sense of direction of the couple moment is the same as that of the resultant force and negative value if the sense of direction of the couple moment is opposite to that of the resultant force. Submit Ii Units My Answers Give Up μA Value Units My Answers Give Up Determine the point where the wrench intersects the x-z plane. Enter the x and z coordinates of the point separated by a comma using three significant figures. 15. ΑΣΦ 41 P vec My Answers Give Up ? 1 ? ? m Provide Feedback Continue
As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 200KN was applied. Find the vertical movement of W. Given: Reqd: Bronze A = 900 sq.mm E =120 GPa 1.5m B L = 1.2m 3.0 m Vertical movement of W W Steel A = 500 sq.mm E = 200 GPa L= 4m -final position 2m... W = 200 KN Meeting in CE397 R2
I need correct answer
Please explain with full detail step by step so I can understand, the answer should be 1800 ksi
a. Computation must be complete.b. Answer in three decimal places.c. Box your final answer.
SITUATION. The figure shows a pellet about to be fired from a sling. The total unstretched length of the rubber is 60 mm. The rubber elongates 1 mm for every 15 N force. Length a=100 mm, b=40 mm. a
A crate weighs 655 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 48 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom cc i❀O ↑Z CC BY NC SA a b с с 6 The tension in rope AC is 조 Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 44 in 35 in 12.1 in The tension in rope AB is The tension in rope AD is χ lb lb a lb D
Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected totension.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension force.
The maximum allowable tensile force in the members of the truss is (Ft)max = 1700 lb, and the maximum allowable compressive force is (Fe)max = 1000 lb. (Figure 1) Figure 1 of 1 Part A Determine the maximum magnitude P of the two loads that can be applied to the truss. Take a = 8 ft. Express your answer in pounds to three significant figures. P = Submit Provide Feedback Π| ΑΣΦ ↓↑ vec Request Answer C ? lb
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?
H.W.# 2: Find the value of force (P) shown in figure if you know that the middle part of the rigidly fastened shaft is stressed to 400 Mia of tensile stress. Then calculate the stress in each of the other two end parts. = 40 mm² 10 kN A = 80 mm² A = 40 mm² 22 KN