A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d2 of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d, of the tube is equal to T = T3 = 1000 lb-in. 800 lb-in. 500 lb-in. 500 lb-in. 800 lb-in. T = TA= Ts = B D C d2 = 1.0 in. 0.697 in

A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d2 of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d, of the tube is equal to T = T3 = 1000 lb-in. 800 lb-in. 500 lb-in. 500 lb-in. 800 lb-in. T = TA= Ts = B D C d2 = 1.0 in. 0.697 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
PROBLEM 3 A compound shaft consisting of a 50mm diameter bronze segment and a 75mm diameter aluminum segment is subjected to two torques shown. Determine the maximum permissible value of T if the stress of bronze is limited to 60Mpa, the stress in aluminum is limited to 70mpa and the angle of twist of the free end is 10 deg. G for aluminum= 28GPA and G for bronze = 35 GPa. 27 37 Aluminum bronze it 2M 2
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that di =50 mm and d2 =30 mm, find the average normal stress at the midsection of (a) rod AB (b) rod BC A 300 mm -d, В 5OKN 150 mm 30KN
Below is another BA bar attached to the AD bar. Diameter of DA bar is 0.02M. A force F = 1000N is applied in the negative x direction at the end of the DA bar and a force P = 500N in the negative y direction at point B. Assuming that the DA bar is made of a ductile metal, find the safety coefficient of the bar by calculating the Von Mises stress at O point. (AD bar material is cold drawn AİSİ 1040 steel.)
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=79, T2 =14, T3 =23 Note: round off your answer to whole number T2 Nm | T3 Nm T1 Nm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
Question #4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. O 2. T a 0.5m 0.5m 30 kN 2 m 100mm 50mm I 10mm 10mm 180mm Section a-a 10mm
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm