A beam from the exterior balcony of a house has a base of 300 mm and a height of 500 mm reinforced with 6-Ø16mm bars for tension and Ø12mm. Determine the following (f'c=20.7 MPa and fy= 415 MPa) using all the NSCP provisions and if the bars is found out to be in two-layers rebars may be unequally distributed on each layer: a. Depth of Tension zone b. Actual Tension Steel Stress c. The net tensile strain d. The ultimate moment capacity of the beam

A beam from the exterior balcony of a house has a base of 300 mm and a height of 500 mm reinforced with 6-Ø16mm bars for tension and Ø12mm. Determine the following (f'c=20.7 MPa and fy= 415 MPa) using all the NSCP provisions and if the bars is found out to be in two-layers rebars may be unequally distributed on each layer: a. Depth of Tension zone b. Actual Tension Steel Stress c. The net tensile strain d. The ultimate moment capacity of the beam

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Problem 3.2 (CE BOARD NOVEMBER 2003, CE BOARD NOVEMBER 2004) The lower ends of the three bars shown are at the same level before the 18 Mg block is attached. Each steel bar has an area of 600 mm 2 and E = 200 GPa. For the bronze rod, the area is 900 mm^2 and E broaze = 83 GPa. Fteel steel Sm a) Find the stress in the bronze rod. b) Calculate the axial stress in the steel rod c) Detemine the elongation of each rod.
4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the corresponding change in length of the aluminum rod. 0.5 m Aluminum A = 2.0x10-3 m2 E 70 GPa a= 23x10-6/Oc + 0.3 m Bronze A = 1.5x10-3 m2 E = 110 GPa d=18x10-6/0c .0 mm
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Stress Analysis of Trusses ANSWER IN 15 MINS