An aluminum alloy pipe with an outside diameter of 5.2 in. and a wall thickness of 6/16 in. cantilevers upward a distance of L = 21 ft. The pipe is subjected to a wind loading that increases from WA = 15 lb/ft at its base to wg = 23 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB B WA Answer: (a) Qmax = (b) Tmax= A L in.³ psi

An aluminum alloy pipe with an outside diameter of 5.2 in. and a wall thickness of 6/16 in. cantilevers upward a distance of L = 21 ft. The pipe is subjected to a wind loading that increases from WA = 15 lb/ft at its base to wg = 23 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB B WA Answer: (a) Qmax = (b) Tmax= A L in.³ psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Kindly quick as possible
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
Determine normal stresses at A and B. Are these point of maximum and minimum normal stresses? If not where are they located and what their values.
Thank you po
A 2024-T4 aluminum tube with an outside diameter of 2.4 in. will be used to support a 30-kip load. If the axial stress in the member must be limited to 17.5 ksi, determine the wall thickness required for the tube.
An aluminum alloy pipe with an outside diameter of 4.3 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 22 ft. The pipe is subjected to a wind loading that increases from wA = 8 lb/ft at its base to wB = 12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
Determine the cracking moment for the figure shown if it is a normal weight concrete with fc=4,000psi. 8 in. 8 in. 24 in. 3 #10 8 in. 3 in.: ⒤갓⒤갓⒤뀐⒤뀐⒤ 6 in. 15 in. -16 in.-
An aluminum alloy pipe with an outside diameter of 4.0 in. and a wall thickness of 6/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 11 lb/ft at its base to wB = 17 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths