A- Answer (1) or (2) 1. For a digital signal (101100111001100010) use DPSK to transmit and receive this signal including the necessary circuit diagrams? 2. If there are digital bits wanted to be transmitted using all kinds of shift keying. Make a calculation for the basic parameters of all e.g. BW, SNR, Probability of error? Assume all the missing values ?

A- Answer (1) or (2) 1. For a digital signal (101100111001100010) use DPSK to transmit and receive this signal including the necessary circuit diagrams? 2. If there are digital bits wanted to be transmitted using all kinds of shift keying. Make a calculation for the basic parameters of all e.g. BW, SNR, Probability of error? Assume all the missing values ?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F= YO Y Y, Y, D. Y. Decoder O a. B' O b. C O'c.B O d. C
Perform the following functions:a. What will be the parity of the data signal to send as even parity:10111010101(0110)BCD = (---?---)2 = (---?---)Excess-3 = (---?---)Grayb. How to represent following numbers in signed representation:1. (-25)102. (-63)10
Parts A ,B , and C. How is -89 represented using 8-bit two's compliment? (The answer should be 8 binary digits) Assume we are using the simple model for floating-point representation as given in the text (the representation uses a 14-bit format, 5 bits for the exponent with a bias of 15, a normalized mantissa of 8 bits, and a single sign bit for the number): Show how the computer would represent the numbers 100.0 using this floating-point format. Express the answer in hexadecimal using 4 hex digits. Suppose we are working with an error-correcting code that will allow all single-bit errors to be corrected for memory words of length 7. We have already calculated that we need 4 check bits, and the length of all code words will be 11. Code words are created according to the Hamming algorithm presented in the text. We now receive the following code word: 01111010101 Assuming even parity, according to our error-correcting code, in what bit is the error? Number the bits from the right…
Question No 1. A) Describe encoding technique (Digital Data to Digital Signal) and explain about Line coding technique. B) What is the difference between NRZ-I & NRZ-L, explain with example.
QUESTION 11 Describe the effect of sampling rate and quantizer bit number on the quality of the generated digital signal. For the toolbar. press ALT+F10 (PC) or ALT+FN+F10 (Mac).
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
4. A data signal with bipolar voltage levels is shown below. The decision threshold is 0 volts. The logic levels are +1 volt for logic 1 and -1 volt for logic 0. Noise with the P.D.F. shown corrupts the signal. Find the probability of error at some instant of time on the condition that logic 0 is sent. LOGIC 1 +1 VOLT -2 1/2 دمت ~IN kla THRESHOLD +2 NOISE P.D.F. -I VOLT. LOGIC 0
In a multiplexer table, when the enable bit is 1, will the output for that bit be 0?
Make a signal flow diagram out of the data. Label everything properly.
• The input to the Encoder is (1), _lines and the output is (2) _lines. • The input to the Decoder is (3). input lines and (4)_ output lines. The multiplexer has (5), output and (6). _inputs.
ii) We want to digitise a signal that contains frequencies between 100 Hz and 1500 Hz, assuming 16 bits per sample. The digitised signal will be transmitted using a QPSK process. Determine the bit rate and the level rate.
Consider error control methods in digital signal transmission. Assume Hamming code is used with even parity. (a) Assume the received code word is 1110101001, determine if the code word is correct. If no, identify the wrong bit and obtain the original data word. (b) If the analogue signal before digitalisation is of frequency from 200 Hz to 1.5k Hz. What is the lowest sampling frequency? (c) Following (a) (b), determine the bandwidth requirement for transmitting the digital message.