(A) A uniform rod 4 m long slender rod AB of mass 40.775 kg is rigidly connected to the center of a think disk of mass 30 kg as shown in the figure. The diameter of the disk is 2 m. At the instant shown the counterclockwise angular velocity of the disk is 10 rad/sec. • (a) Find the resultant acceleration of the center of the rod AB and • (b) determine the support reactions at A. Im в 200 kg

(A) A uniform rod 4 m long slender rod AB of mass 40.775 kg is rigidly connected to the center of a think disk of mass 30 kg as shown in the figure. The diameter of the disk is 2 m. At the instant shown the counterclockwise angular velocity of the disk is 10 rad/sec. • (a) Find the resultant acceleration of the center of the rod AB and • (b) determine the support reactions at A. Im в 200 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
4 -(Kinetics of Curvilinear Motion) Tow weights W, and W2 of 8KN and 5KN are attached at the ends of a flexible cable. The cable passes over a pulley of 100 cm diameter. The weight of the pulley is 600N with a radius of gyration of 50cm about its axis of rotation. Find the torque which must be applied to the pulley to raise the 8KN weight with an acceleration 1.5 m/s?. Neglect friction in the pulley bearing. 50 cm 600N T 8kN 5kN W,
Given: A uniform slender rod is at rest upon a frictionless horizontal surface when a force (F) is applied in the direction shown. Assume that the rod has mass m and length L. A L Horizontal Plane Given that F = 74lb, L = 7.1 ft, mg = 4.6lb, and 0 = 73deg What is the component of acceleration of the mass at point G in the i direction? Answer: Check What is the component of acceleration of the mass at point G in the j direction? Answer: Check What is the component of angular acceleration of the mass in the k direction? (remember your signs) Answer: Check
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
PROBLEM 2 For the mechanism, shown on the figure, @nc = const=5s. O4-BC-0,3 m. AB 0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body O4: d) linear velocity and acceleration of the point 4. 120
A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2 = 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of Ö . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of N = 1 rad/s. Ring R XG A 1 Ixx = lyy =mR? G Iz = mR?
A body of M.I. 4 kg m? rotates with a uniform angular velocity of 20 rad/sec. when an external torque 10 Nm is acting on it. If the external couple is removed calculate the time taken to stop and the total angle by which it rotates before it stops.
A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.
In the mechanism shown in the figure, the OE crank rotates with a constant angular velocity of 3 rad/s. At the moment shown:a. find the velocity of the Point C, which is the center of mass of the disk, andb. find the angular acceleration of the disk.
Consider the wheel shown below with radius R, mass m, and radius of gyration ko¹ The wheel rolls without slipping under the action of a clockwise torque M. At the instant shown the spring with spring constant ks is unstretched. Derive an expression for the velocity of the wheel center of mass G after the center of mass has moved a distance d. (Hint: Use rigid body work-energy principles. The work done to the system by the applied moment is McA0 and A0 can be related to the distace d by the no-slip condition.) Us G R M м, ко ////
Consider a steel plate of mass m with dimensions L and w that is equally supported by two ball bearings (one on each end of the shaft shown at pointa A and B). At the instant shown below, the plate is released from rest. Part A: Determine an expression for the plate's angular acceleration magnitude a at this in- stant. (Hint: Use Euler's 2nd Law for pinned rotation and the parallel axis theorem.) Part B: Show that the magnitude of the reaction force at each bearing at this instant is R = mg/8. (Hint: Use the kinematics to relate the acceleration of the center of mass G to the angular acceleration. Use Euler's 1st Law to find the reaction forces with the acceleration you determined. As viewed from the side there are two forces acting on the system weight and two reaction forces both pointing upward at the same location.) A foye مر B L २