A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2= 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of ë . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of 2 = 1 rad/s. Ring YG R G XG A Ix = lyy =;mR² I = mR?

A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2= 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of ë . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of 2 = 1 rad/s. Ring YG R G XG A Ix = lyy =;mR² I = mR?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The 30-in slender bar weighs 20 Ib, mounted on a vertical shaft at O initially rotates at w = +10 rad/s. If a 12" torque M = +100 lb-in is applied to the bar through its shaft, calculate %3D 18 the reactions at O after the bar rotates for 1 sec.
SECW OM A motorbike wheel with an 8 kg mass has a 0.4 m radius of gyration around the z-axis, as shown in Figure. The wheel's shaft is supported by bearings A and B and rotates at a constant rate of 150 rpm in a counter-clockwise direction from the z-axis, while the frame rotates at 12 rpm in a counter- clockwise direction from the y-axis. Determine the resultant reaction forces at each bearing A and B due to the mass and gyroscopic effects. With the result of forces, which bearing has a tendency to fail first, which bearing should be considered for design purposes and explain the effect on motor if the bearing fail. y 0.55 0.4 All dimensions in meter (m)
An uniform W=14 kg rod is supported by a ball-and-socket joint at A, and by the cord CG that attached to the midpoint G of the rod and by the frictionless wall at B. Given, x=562 mm, d=132 mm and g=9.81 m/s². What is the magnitude of z-component of reaction force at B? Put your answer up to 2 decimal points. 'd' mm 150 mm B 400 mm 'x' mm 22
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
The uniform slender rod, witha mass of 9.6 kg and a length ofE = 0.76 m, is fixed to a light vertical shaft at 0. The shaft can rotate freely in the stationary socket on the floor. A constant moment of M 11.8 N m is applied to the shaft, as indicated. What is the magnitude of the angular acceleration (in rad/s) of the rod? The rod moves in a horizontal plane.
if mass (m)=345kg radius of gyration kG = 0.54 m θ= 200 degree Tmin=1523 N assuming no slipping 1) Find aG, α, the value of the friction force (f) and the normal reaction force on the spool by the ground if T = 0.5 Tmin.
Q1/ A compressor has three inline pistons of mass 40x 104 mg, with a crank radius of 0.04 m and ratio n of 4. the crank is equally space in angle and positioned as show. Determine the primary and secondary force and turning moment about the reference plane X when it revolves at 8.33x10 3 rad/h. KI 120° 120° K2 120° K3 KI= 5 cm. K3= 150mm, K= 0.1 m, K4= 50 mm
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The 0.4 kg B pin in the figure moves freely inside the circular slide DE with radius b and the counterclockwise (positive direction) rotating arm OC. Calculate the radial (Fr) and axial (Fθ) forces using the values in the table, ignoring friction. b=211 mm θ=19 θ.=9 rad/s θ..=285 rad/s2
A beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables available in the palette. e. Enter an expression for the vertical component of…
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm