(a) A bar AISI 1035 steel forged and heat treated with minimum yield strength of_MPa is subjected to bending moment of _Nm and a torsional moment of Nm. Assuming a factor of safety of 2, determinethe diameter of rod using thefollowing theories of failure (i) Maximum Shear stresstheory and (ii) Distortion Energy theory (ii) Maximumstresstheory, alsospecifywhich diameter is considered as safe yield strength = 555MPA bending moment = 285NM torsional moment = 315NM

(a) A bar AISI 1035 steel forged and heat treated with minimum yield strength of_MPa is subjected to bending moment of _Nm and a torsional moment of Nm. Assuming a factor of safety of 2, determinethe diameter of rod using thefollowing theories of failure (i) Maximum Shear stresstheory and (ii) Distortion Energy theory (ii) Maximumstresstheory, alsospecifywhich diameter is considered as safe yield strength = 555MPA bending moment = 285NM torsional moment = 315NM

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1045HR steel bar has a diameter of 40mm and it will be put under a fully reversible torsional load at 85000 cycles in an operating environment at 300 °C, estimate the limit of fatigue strength and fatigue strength'at 85000 cycles. I need detailed and correct answer if your answer is wrong I gives u 10 downvotes so please be carefully do
On average, you inhale approximately 1 L of air every 2 seconds. The pressure difference between the outside air and your chest cavity creates this flow. The air flows through your trachea which has a radius of 0.005m and a length of 0.12m. Do not ignore the viscosity of air in this problem. a. What is the velocity of the air moving through the trachea? b. Is this flow laminar or turbulent? Support your answer with calculations. c. What is the pressure in your chest cavity required to create this flow? Assume the outside air has a pressure of 1 atm.
Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion- energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x = -46 MPa, Oy = -80.5 MPa, and Txy = -46 MPa The factor of safety from the maximum-shear-stress theory is 3.56, and the factor of safety from the distortion-energy theory is 3.3
Problem 19.1 The shaft shown in the following diagram is supported by two self-aligning bearings at A and B and is subjected to the loads shown on the chain sprockets. 50 mm 100 mm. 100 mm F 30 mm 3000 N 100 mm 50 mm
A bar AISI 1035 steel forged and heat treated with minimum yield strength of 570MPa is subjected to bending moment of 290Nm and a torsional moment of 310Nm. Assuming a factor of safety of 2, determine the diameter of rod using the following theories of failure (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory, also specify which diameter is considered as safe
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
Please answer asap I will give u ggod rating if u do not copy. thank u and please solve by yourself.
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 30 mm, and the rod length was 300 mm. When the applied torque reached 260.8 N·m, a shear strain of 1605 microradians was measured in the specimen. What was the angle of twist in the specimen?
Problem 2 A 1.5-in-diameter bar has been machined from an AISI 1050 cold-drawn bar having a yield strength of 84 kpsi and ultimate strength of 100 kpsi. This part is to withstand a fluctuating tensile load varying from 0 to 16 kip. Knowing a fatigue stress-concentration factor K, is 1.85 for 106 or larger life. The Marin factors are: K₂= 0.8; K=1; K=K=K₂=K=1. Estimate the factor of safety guarding against fatigue and static failures using the Gerber and Langer failure criteria.