A 6-bit Flash ADC has - possible output codes. a. 63 b. 64 C. 6 d. 65 While using ARDUINO UNO to read from a 5V sensor, the analog read () has a count value of 480. What is the voltage applied on the pin? a. 42.3 V b. 104 V 3.76 V d. 2.34 V In PIC16 data memory, all the Special Function Registers are in Bank 0. a. True O b. False

A 6-bit Flash ADC has - possible output codes. a. 63 b. 64 C. 6 d. 65 While using ARDUINO UNO to read from a 5V sensor, the analog read () has a count value of 480. What is the voltage applied on the pin? a. 42.3 V b. 104 V 3.76 V d. 2.34 V In PIC16 data memory, all the Special Function Registers are in Bank 0. a. True O b. False

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

what is the MAXIMUM number of diode OR gates that can be cascaded before the output is not recognized as logic high?
Discuss in detail about RAM allocation in 8051 and Analyse, and explain the objective of the following 8051 assembly language program. Specify the content of the Program Status Word (PSW) register after the execution of each instruction. ORG 00H MOV A#00H MOV R5,A MOV R0,#0FBH ADD A#0FEH JNC NI INC R5 N1: ADD A, #0F5H JNC N2 INC R5 N2: ADD A#0F2H INC OVER INC R5 OVER: MOV @R0, A END Comment every line of the program and specify the register contents on single-step execution.
An 8051 micro,controller must be connected to a latch, an EEPROM, a RAM memory, a keypad and encoder and an ADC. Figure 2.1 shows the different components. For the arrangement to work the components must be connected to the address bus, the data bus, the decoder and the microcontroller. The RAM must be connected to address 0x0000 to 0x3FFF, the keypad and encoder to address 0x4000 and the ADC to address 0x6000. The program that must be executed is in the EEPROM. A crystal must also be connected to the microcontroller. Complete the circuit diagram by connecting all the pins of the controller and the devices to the correct pins/lines. The missing pin names and line numbers must also be filled in on the controller and devices.
In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC C-Connected to LOGIC State D-Connected to LOGIC Probe
Number of output pins in IC74153. Options A-1 B-2 C-3 D-4
Please show work included 6. Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature over a range of -27oF to 100oF. If the actual temperature being read was 40oF, what would be the closest possible value that the system could represent? Write the answer in a 7-bit binary number as well as in decimal. The answer should be in the following form 00010001 and -10oF a set of two numbers.
DIsassemble the following MIPS 32-bit hexadecimal instruction written as addr:instr 60005000 : 0c000020
Write an Assembly Language for 8051 Microcontroller which copies the data from R0 of Banko to R1 of Bank1, R2 of Bank 2, and R3 of Bank 3.
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
Q1/ Answer the following questions? 1. List and explain LCD registers? 2. Human eyes emitenergy and are detected by ---- 3. Define Common cathode 7-Segment? 4. List 3 applications of microcontroller? 5. Ultrasonic include ----, - Q2/ How can we connect LDR with PIC Microcontroller? Q3/design control circuit by MC to operate 2 LEDs connected to pins AB and A4 of PIC16F84A.
An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
Match each of the various types of ROM with the best description. MROM PROM EPROM EEPROM flash EEPROM A. programmed by burning fuses B. must be removed to be reprogrammed C. single bits can be erased D. the whole chip can be erased without removing it E. only econonical for large batches of chips