A 572 Grade 65 steel with Fy = 448 MPa is used as a simple beam to carry a concentrated load P at the center of its span on a 6m simply supported span. The beam is W 12 x 14 section having the given properties shown. Properties of W 12 x 14 Weight of beam = 204.76 N/m Area = 2658 mm2 Depth (d) = 302.514

Q: 1- Given Data Ꭰ L 40 in × 30 in fy Column = 350 Kips = 250 Kips = 60 ksi fé fy qa Footing = 3.25 ksi…

A: Data provided -column                                  Footing                                1Ksf…

Q: PROBLEM NO. 2 [1-j GIVEN: B= 2 j FIND: DET B. A) 4 + 6j 1-j 1+j j 1+j 1 j B) -4 + 6j C) 4 - 6j D) -4…

A: Det…

Q: Determine the diameter (mm) of the cables so that the stress at each cable will not exceed the…

A:

Q: For a constant specific energy of 1.20 m in a rectangular channel 3 m wide, calculate the critical…

A: This question is from fluid engineering Specific energy is 1.20 metre in with the channel is equal…

Q: b ▼ 2m 2m 2m 15m a

A: Different types of forces acts on a dam structure such as water pressure, self weight, wave pressure…

Q: A P a B Ь W с Х

A: Find the shear and moment equations for the beam loaded as shown if P = 494 lb, W = 169 lb/ft, a =…

Q: 1. The figure below has an area of mm² for all members. Determine t stress induced of member AF and…

A:

Q: Determine the support reactions with explanation

A: Given A beam Required  Support reactions

Q: Problem 1. Determine the exact plastic collapse load, Pu, of the beam in Figure 1, where a is a…

A:

Q: Required information The rotating-cylinder viscometer in the image shears the fluid in a narrow…

A: Given:- The rotating-cylinder viscometer shears the fluid in narrow clearance ∆r The magnitude of…

Q: 10. Determine the cross-section of a rectangular beam loaded as shown in the figure if the allowable…

A: Shear stress and bending stress The outcome of a load applied perpendicular to a member is normal…

Q: he beam shown, determine ration method. Assume a 60K

A:

Q: A jet of water is ejected out of the tip of a nozzle (50mm in diameter) and exposed to the…

A:

Q: ing moment that occ

A:

Q: Compute the force in members CE, BD, and CD by method of sections in the truss shown.

A: Tension and compression member forces signs : Away from the joint : positive (Tension )  Towards the…

Q: A T-beam (internal) for a floor system has a slab thickness of 100mm and a total depth of 550mm. It…

A: T-Beam T-beams are constructed up of a flange and a rib in the shape of a T, and are usually built…

Q: et is issued from the side of a tank under a constant head as shown in the figure. The side of the…

A:

Q: (3) Use Virtual Work to determine slopes at A, B and C, and the displacement at C. Check all results…

A: As per policy, only one question can be answered. For solution using the moment area method kindly…

Q: The Portland Cement Association recommends a minimum cement content of for concrete placed under…

A: Minimum cement content is 564 lb/yd^3

Q: A settling tank having a depth of 3.5m and surface area of 1000m^2 is used to remove particle of…

A: Given:- The depth of the settling tank = 3.5 m  The surface area of the tank = 1000 m2  The size of…

Q: SYSTEMATIC ERRORS IN TAPING + TAPE IS NOT OF STANDARD LENGTH A building 38 × 45 m is to be laid out…

A:

Q: 1. Find and solve at least 3 problems for Methods of Sections and 2 problems for Area method

A: This question is from Structural analysis.

Q: (a.1) Find the probability that the elongation of a steel bar is above 0.1 inch. (a.2) Find the…

A:

Q: Find pressure value Force=2.11 N Area 0.223 m2

A: Given data-  Force (F) = 2.11 N  Area(A) = 0.223 m²

Q: Q3. A sphere is tested for drag resistance in a the wind tunnel. A pressure tapping at the…

A: Given :

Q: Problem A barge shown supports the load W1 and W2 for every one-meter strip along the longitudinal…

A:

Q: A Marshall specimen is prepared for bituminous concrete with a bitumen content of 5 percent by…

A: given Bitumen content wb=5%theoretical unit weight γt=2.442 g/cm3measured unit weight γm=2.345…

Q: The shaft is solid for CB and hollow for BA (See Section a-a) where L = 0.75 m. If the shaft is made…

A:

Q: Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev.…

A: Given  rate of flow from z = 605L/sec Ele = 282m

Q: a section 2.07 m from A if P = 5470 N. W=2372 N/m, a = 1.2 m, b = final answer to two decimal…

A:

Q: In a city, the population to be served: 78,320 and per capita waste generation is 0.85 kg/capita/day…

A:

Q: ! Required information Sometimes equations can be developed and practical problems solved by knowing…

A:

Q: a) What is light pollution and its effects towards human, social, economy and environment

A:

Q: Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is…

A: Solution: Given: DL = 5.3 KPa LL = 2.4 KPa fc = 21 MPa fy = 345 MPa beam = 350 x 500 mm use 12 mm…

Q: Find the optimum duration and cost for the projects of a 11 activities, the indirect cost = 150 $…

A:

Q: Please define the term of anisotropy and bending stiffness.

A: anisotropy, in physics, the quality of exhibiting properties with different values when measured…

Q: The cross section at the midspan of a simply supported beam is shown below. It is reinforced with…

A:

Q: b = 440 mm • d = 644 mm • f'C = 26 MPa • fy = 413 MPa • As = 7-25mm dia. • As' = 3-25mm dia.…

A: This question is from reinforced concrete structures.

Q: A Spiral column is to be loaded with DL=400Kn and LL=500Kn with minimal reinforcement. The Design…

A: DL = 400 KN LL = 500KN

Q: A metal bar of length 100 mm is inserted between two rigid supports and its temperature is increased…

A:

Q: (h) The ordinates of a 2-h unit hydrograph are given below. Time (hrs) 0 2 2-h UH ordinates 0 25 4 6…

A: Given data:- Below table is given; Time (hrs) 0 2 4 6 8 10 12 14 16 18 20 22 2-h UH ordinates…

Q: Normal and shear stresses acting at the point is shown in Figure 1- Determine the principal stresses…

A:

Q: For each of the following transfer functions with zeros, find the component parts of the unit step…

A: It is given that ;

Q: For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.56 in from…

A:

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a 90-degree triangular…

A:

Q: A load P is supported by two steel springs arranged in series as shown. The upper spring has 20…

A: Given data:- For Upper spring; No. of turns, n =20 Diameter of wire, d = 20 mm Mean diameter, D =…

Q: A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness confined between…

A:

Q: Y A x C Given: x=2.335 m, y = 2.335 m w= 2.771 kN T= 160.983 MPa F.S. = 2.46 Required: Diameter of…

A: Let's draw the FBD of the given structure for better understanding For the equilibrium of static in…

Q: It is desired to pump 390 liters per second of water from a stream to a pool as shown in the figure…

A: Q = 390L/s = 0.39m3/s

Q: Problem Solving: Water flows over a rectangular weir 1-m wide at a depth of 150 mm and afterward…

A: The given data is shown below: Width=1mDepth=150mmCd=0.62 and 0.59