A 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in terms of head in meters of the oil. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 B.

A 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in terms of head in meters of the oil. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ubject Date No. The water mercury manometer of Frgure shown Indicates a differential reading of o.30m when the pressure in pipe A is 0,30m 30 Hg vacuuem Determine mm the pressure in pipe B in Kpa ? tmercury
Šubiect No. Bubject Date No. An open manometer, shown în the Dright figure, is in stalled to measure D pressure in a pipe canrying (sp.gr=0.82). If the manometer liquid is carbon tetra chlovide (sp.gr=lo6o) determine the pipe pressure (in meters oil of water- colunn heig ht) an oil 11 Air > 66 Cm imanometer liquid
Q3- The mercury manometer of figure indicates a differential reading of 0.30 m when the pressure in pipe A is 30-mm Hg vacuum. Determine the pressure in pipe B. Oil Water 0.50 m tB l0.15 m 0.30 m Mercury
A cylindrical tank contains water at a height of 55mm as shown. Inside is a small open cylindrical tank containing cleaning fluid (s.g.-0.8) at a height h. The pressure Pb-13.4 kPa gage and Pc-13.42 kPa gage. Assume the cleaning fluid is prevented from moving to the top of the tank. (a) Determine the pressure Pa in kPa, (b) the value of h in mm, and (c) the value of y in millimeters
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in kPa? A 2.75 h B Hg(13.6)
Figure Q1 (a) shows the tank attached with piezometer tubes. The pressure gauge A is 2.3 kPa. The specific weight for the air is 12.0 N/m', the specific weight for gasoline is 6670 N/m³ and the specific weight for the glycerin is 12360 N/m³. Find the elevation level, ZB and Zc of the liquid (in meters) in the open piezometer tubes B and C. A B C 2 m Air 1.5 m Gasoline ZB Zc 1 m Glycerin Figure Q1 (a)
A 4m Oil (0.90) 3.75 mm B Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in bar. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: bar Decimal Places required in the final answer: 3
Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage.Determine the value of H in m if the pressure at A is 142 kPa. Round your answer to 2 decimal places.
Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage. Determine the value of H in m if the pressure at A is 142 kPa.
Problem 5. For the setup shown, a manometer was attached from a tank into a pipe. Assuming standard conditions, determine the absolute pressure at A. Air -Hg 140 mm H,0 -Oil specific gravity - 0.83 а. 600 mm 90mm 200 mm Fie
1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft