A 480-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 110-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.)

A 480-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 110-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.17P: .17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the...

See similar textbooks

Similar questions

A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
A 540-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 140-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.) (a) Find the (magnitude of the) tension T in the cable.N(b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component _____N vertical component _____N
A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a diameter of 1/2 in. The bolt connecting the top yoke and the bottom strap has a diameter of 5/8 in. The bottom strap is 3/16 in. thick by 1.75 in. wide by 36 in. long. The weight of the pipe is 2,000 lb. Determine the following: (a) the normal stress in the hanger rod, (b) the shear stress in the bolt, (c) the bearing stress in the bottom strap.
A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a diameter of 1/2 in. The bolt connecting the top yoke and the bottom strap has a diameter of 5/8 in. The bottom strap is 3/16 in. thick by 1.75 in. wide by 36 in. long. The weight of the pipe is 2,000 lb. Determine the following: (a) the normal stress in the hanger rod, (b) the shear stress in the bolt, (c) the bearing stress in the bottom strap. Show FBD
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.
The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of materials. E1 = 70 Gpa and E2 = 210 Gpa. P = 100 kN axial compressive force It affects the C point. The diameter of the circular bars is D1 = 80 mm, D2 = 40 mm and their length L1 = 20 cm. and L2 = 30 cm. (The direction of the force P is in the negative x-axis direction.) a) What are the displacements at B and C points? b) What is the reaction force at point A? c) What are the stresses in the bar?
A utility hook was formed from a round rod of diameter d= 0.75 in into the geometry shown in the figure. Given: F= 1500 lbf, L = 7 in, and D;= 2.5 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. L.
A polyethylene bar having rectangular cross section with a width 6.36 in. and depth 6 in. is centered inside a hollow steel square section with side dimension of 7 in. The polyethylene bar is then compressed by an axial force P. 0.3 in. 6 in. 7 in. 6.36 in. 7 in. At what value of the force P will the gap between the polyethylene bar and the steel tube be closed for the first time in one dimension? For polyethylene, assume E = 200 ksi and v = 0.4. Assume that the material behaves linearly elastically. (Enter the magnitude in kips.) kips What is the remaining gap between the polyethylene bar and the steel tube in the other dimension? (Enter the distance in inches between the side of the polyethylene bar and the closest side of the steel section.) in.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 45846-Nload, using the following data: length of steel = 11 m, length of bronze = 2.3 m Area of steel = 562 mm, Area of bronze = 335 mm Modulus of elasticity of steel = 195 Gpa, Modulus of elasticity of bronze = 80 Gpa x= 0.55 m, y = 1.12 m, and z = 0.78 m. Round off the final answer to two decimal places. ... Bronze Steel
The bar rests against a 6-27 The bar shown in Fig. smooth vertical wall at end D. The support at A is a ball- and-socket joint. The cable is not continuous at B. D