A 40-mm-diameter solid shaft is subjected to an axial force of P- 2480 N, a vertical force of V- 1880O N, and a concentrated torque of T-66 N-m, acting in the directions shown. Assume L- 130 mm. Determine the normal stress o, at point i H. O 29.3 MPa 44.7 MPa 40.9 MPa 34,7 MPa 55.9 MPa

A 40-mm-diameter solid shaft is subjected to an axial force of P- 2480 N, a vertical force of V- 1880O N, and a concentrated torque of T-66 N-m, acting in the directions shown. Assume L- 130 mm. Determine the normal stress o, at point i H. O 29.3 MPa 44.7 MPa 40.9 MPa 34,7 MPa 55.9 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

View Policies Current Attempt in Progress A 30 mm diameter solid steel shaft supports loads P = 3000 N and Q = 5100 N as shown. Assume L = 600 mm. The bearing at Bcan be idealized as a roller support and the bearing at D can be idealized as a pin support. The moment of inertia of the shaft is 39760 mm4. Determine the magnitude of the maximum bending stress in the shaft. В Answer: Omax = i MPа Save for Later Attempts: 0 of 1 used Submit Answer
A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is sleep over a solid steel shaft 50mm in diameter and of the same length as the hollow shaft. The two shells are then fastened rigidly together at their ends. Determine the maximum shearing stress developed in each material by end torques of 3 KN-m. For bronze G=35GN/m2 and for steel G=83GN/m2. Answers should be in MPa.
A solid shaft has diameter of 80 mm. it is subjected to a torque of 4 kN-m. The maximum shear stress induced in the shaft would be A 75/π N/mm 2 B 125/π N/mm² C 150/π N/mm D 250/π N/mm²
View Policies Current Attempt in Progress A solid circular steel shaft having an outside diameter of D = 1.25 in. is subjected to a pure torque of T = 2390 Ib-in. Determine the maximum shear stress in the shaft. O 5.25 ksi O 5.64 ksi O 4.37 ksi O 8.67 ksi O 6.23 ksi
T' T An aluminum alloy shaft has an allowable shear stress of Tallow= 100MPa. If the diameter of the shaft is 100 mm and a 75 mm diameter hole were bored through the shaft, determine the maximum torque T that can be transmitted. Give your answer in N.m.
3. A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is slipped over a solid steel shaft 50mm in diameter and of the same length as the hollow shaft. The 2 shafts are then fastened rigidly together at their ends. Determine the maximum shearing stress developed in each material by end torques of 3KN-m. For bronze G=35GN/m2 and for steel G=83GN/m2. Answers should be in MPa " 75 mm o T=3 kN.m 50 mm ø T=3 kN.m B Steel C Bronze G=35 GN/m? G=83 GN/m2
A solid 1.00 in. diameter shaft is subjected to a torque of T = 240 lb-ft and an axial load of P = 5000 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 = i Tmax in-plane A i H (1) 요. 요.. psi psi T B psi P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A solid 1.250-in-diameter steel shaft is subjected to torques Tg- 190 Ib-ft and Tp- 115 Ib-ft, acting in the directions shown. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque Tethat can be applied to the shaft. Te Tp Ib-ft Answer: Te= i
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.
View Policies Current Attempt in Progress A 40-mm-diameter solid shaft is subjected to an axial force of P = 2410 N, a vertical force of V = 1560 N, and a concentrated torque of T= 65 N-m, acting in the directions shown. Assume L = 130 mm. Determine the normal stress a, at point H. О 34.2 МPа O 31.2 MPar O 40.4 MPa O 42.8 MPa O 46.5 MPa 144 acer
A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Assume TA - 536 N-m, Tg - 1340.0N-m, Tc - 1072 N-m, and To - 268.0 N-m. Determine the magnitude of the maximum shear stress in the shaft. TB Tc Tp (3) (2) B D Answer: Tmax" MPа