A 3 inch diameter steel sphere achieve a terminal velocity of 122 inch per seconds when dropping through it all column of liquid is 87 lbm/ feet cube. The density of steel is 488 lbs per feet cube. The final drag coefficient of the square is most nearly? a. 0.22 b. 0.34 c. 0.40 d. 0.48

A 3 inch diameter steel sphere achieve a terminal velocity of 122 inch per seconds when dropping through it all column of liquid is 87 lbm/ feet cube. The density of steel is 488 lbs per feet cube. The final drag coefficient of the square is most nearly? a. 0.22 b. 0.34 c. 0.40 d. 0.48

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The maximum lift-to-drag ratio of a 600,000 lb aircraft is 18.7. The Thrust Specific Fuel Consumption (TSFC) = 0.85 (lbs/hr)/lb. The total fuel on board is Wf = 180,000 lbs. Find the maximum endurance of the aircraft in hours. Round off your answer in ones place. Answer for a thumbs up
#4 1.11 For a small particle of styrofoam (1 lbm/ft) (spherical, with diameter d = 0.3 mm) falling in standard air at speed V, the drag is given by FD-3mVd, where is the air viscosity. Find the maximum speed starting from rest, and the time it takes to reach 95 percent of this speed. Plot the speed as a function of time. s) Answer: (Vmax=0.0435",t=0.0133 S
An aircraft has a wing area of 70 m? and a wing loading of 2500 N/m2. The air density could be taken as 0.45 kg/m3. The drag equation for the aircraft is given as: Cp-0.016+0.055 C2 Calculate its minimum drag speed in m/s. Keep 2 decimals.
Qustion. An aircraft is flying in level flight at a speed of 200 km/h through air (density, p = 1.2 kg/m³, and viscosity, μ = 1.6 x 10-5 N-s/m²). The lift coefficient at this speed is 0.4 and the drag coefficient is 0.0065. The mass of the aircraft is 800 kg. The effective lift area of the aircraft NOTE= Do not give wrong answer I will dislike , If not sure skip it
The large block shown is x = 72 cm wide, y = 54 cm long, and z = 9.0 cm high. This block is passing through air (density of air p = 1.43 kg/m³) at a speed of v = 8.61 m/s. Find the drag force F41 acting on the block when it has the velocity vj and a drag coefficient I = 0.812. V2 Fa.1 N %3D Find the drag force F42 acting on the block when it has the velocity vz with a drag coefficient I = 0.893. F42 N Find the drag force Fa.3 acting on the block when it has the velocity vz with a drag coefficient I = 1.06. F4.3 = N EN
Q.2 Four cars, with a mass of 1500 kg each, are loaded on a 6 m wide, 12 m long small car ferry. How deep, in cm will it sink in the water? A 15.2 В 11.5 C 10.2 D 8.3
Calculate the minimum flight speed of an aircraft at constant altitude. Consider and aircraft with maximum take-off mass of 40,000kg CL=1.2 and a cruising altitude of 20,000m. The total lifting surface is 200m. Using properties of air from tables at standard atmosphere with 20,000m and -56.50°C. Da. 161.14m/s Ob. 181.14m/s Oc 171.14m/s Od.191.14m/s
The drag polar equation of a light airplane in clean configuration can be written as Cp = 0.358 + 0.0405 C₁². It has a weight of 18,681 N. The wing area is 14.41 m². Calculate the minimum power required in watts. (Round off answer with no decimal places, No units, No commas) Answer given: 1461792 A 5,000 lbs. aircraft has an excess power of 75 hp at sea level. If the service ceiling is 3,657.6 m, determine the time to climb from sea level to absolute ceiling in minutes. (Round off answer with no decimal places. No units, No commas) Answer given: 17
A sphere (Cd = 0.2) 1 ft in diameter travels at 100 ft/sec in standard atmospheric air. What is the drag force? A. 0.0117 lbf C. 0.0712 lbf B. 0.0217 lbf D. 0.0127 lbf
A tremendous force is generated when waterfreezes into ice and expands in volume by 9.0%. Suppose a 1.000-m3cube of liquid water freezes into ice that is 1.000 m on a side by1.090 m tall. How many 68-kg students would the ice be able tolift? Determine this by calculating the amount of force on the top1.000-m2face that would be required to squeeze 1.090 m3of iceback to 1.000 m3, assuming all of the volume change occurs alongthe vertical direction
Hw.1 1. With a starting velocity of 60 m/s, a tiny projectile is launched vertically downward into a fluid medium. The projectile decelerates by a = m/s? due to the fluid's drag resistance, where v is measured in m/s. Calculate the projectile's velocity and position 4 s after it is fired.
Please do this specific question with these specific data as many have post it with different data! The ABC lift is at rest. You want to estimate the momentum that ABC exerts in C if the weight of A is 105 kg. AB is 12.15 m and weighs 400 kg, BC is 2.7 m and weighs 150 kg. Approximate AB and BC as evenly thick everywhere and homogeneous. Point A is 13.5 m above C in height and B is 2,025 m above C in height. A) What is the moment of force that ABC exerts in C if positive value is counterclockwise in the image? B) If AB instead weighs 150 kg and BC weighs 400 kg, but all other quantities are the same, calculate the torque in C.What is the moment of force that ABC exerts in C with these masses, if positive value is counterclockwise in the picture?