A 22 kg compressor impeller wheel is driven by a 13 kg turbine mounted on a common steel shaft, as shown in Figure 1 below. E =207 GPa. Assuming the bearings to be stiff and acting as supports. Calculate: a) The reactions of the supports at A and C [4] b) The shaft deflection at B and D using Macaulay’s method. [11

A 22 kg compressor impeller wheel is driven by a 13 kg turbine mounted on a common steel shaft, as shown in Figure 1 below. E =207 GPa. Assuming the bearings to be stiff and acting as supports. Calculate: a) The reactions of the supports at A and C [4] b) The shaft deflection at B and D using Macaulay’s method. [11

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.11P: B cams AB and CDE are connected using rigid link DB with hinges (or moment releases) at ends D and B...

See similar textbooks

Similar questions

A bumper for a mine car is constructed with a spring of stiffness k = 1120 lb/in. (see figure). If a car weighing 3450 lb is traveling at velocity v = 7 mph when it strikes the spring, what is the maximum shortening of the spring?
A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?
B cams AB and CDE are connected using rigid link DB with hinges (or moment releases) at ends D and B (see figure a). Beam AB is fixed at joint A and beam CDE is pin-supported at joint E. Load P = 150 lb is applied at C\ Calculate the deflections of joints B and joint C Assume L = 9 ft and EI = 127,000 kip-in2. Repeat part (a) if rigid link DB is replaced by a linear spring with k = 20 kips/in (see figure b).
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The figure shows a stepped steel shaft supported in bearings at A, C and loaded by a 2 kN force at B. Use Castigliano's second theorem to find the angular misalignment at the bearings (i.e. the local slope of the beam) due to the shaft deflection. For steel, E 210 GPa. [You may assume that the second moment of area of a shaft is I = Td¹/64, where d is the diameter of the shaft.] = 25 mm 200 mm B 2 kN 15 mm 30 mm 200 mm
A 22.63 kg compressor impeller wheel is driven by a 13.56 kg turbine mounted on a common shaft (see Figure 1.3) manufactured from steel with Young's modulus E = 207 GN/m2. The design speed is 10 000 rpm. Determine the shaft diameter so that the first critical speed is 12 000 rpm giving a safety margin of 2000 rpm. Use Rayleigh's equation and assume rigid bearings and a massless shaft. Compressor impeller Bearing 0? Bearing Turbine 254 mm 254 mm 254 mm Figur 1.3: Turbine shaft.
Problem 3 connected as shown below. Nodes 1 and 3 are fixed (walls). Both elements have Young's Modulus of 30x106 psi and cross-sectional area of 2.0 in?. There is an external force acting at Node 2 of 8000 Ib to the right. Assume that the bars can only undergo translation in x (1 DOF at each node). ASsume +x is to the right. a) Find the displacement of Node 2. Hint: units! b) Find the reaction forces at the walls. Hint: units! FEA 1-D Direct Method Bar Elements. A 1-D bar element system is +x E1 E2 8000 lb 20 in. 50 in.
The complex shaft assembly shown below is made of steel (Gst = 75 GPa). A solid shaft with a diameter of 20 mm is fixed to the tube at point B using a rigid disk. The outer diameter of the tube is at 40 mm, while the wall thickness is 5 mm. Find the: a Polar moment of inertia of the tube, m^4 a. Polar moment of inertia of the solid shaft, m^4 c Angle of twist at D, radians A GAm 150 N-m 0.1 m 0.3 m 50 N-m
The complex shaft assembly shown below is made of steel (Gst = 75 GPa). A solid shaft with a diameter of 20 mm is fixed to the tube at point B using a rigid disk. The outer diameter of the tube is at 40 mm, while the wall thickness is 5 mm. Find the: %3D a. Polar moment of inertia of the tube, m^4 b. Polar moment of inertia of the solid shaft, m^4 c. Angle of twist at D, radians 0.4 m 150 N-m 0.1 m 0.3 m 50 N-m
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…