A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 20 and 15 A respectively and are fed from the cable at distance of 25 and 10 respectively. Calculate the voltage available across load 1 and 2. a- Voltage across load A is, Va= b- Voltage across load B is, Vb=

A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 20 and 15 A respectively and are fed from the cable at distance of 25 and 10 respectively. Calculate the voltage available across load 1 and 2. a- Voltage across load A is, Va= b- Voltage across load B is, Vb=

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

A current is measured at the neutral ground of a star load, of equal impedances in all three phases. Which of the following conditions is NOT possible?A) The currents in the three phases are equal in magnitude and angle.B)One phase of the supply conductors was left in open circuit.C) The line-to-neutral voltages in the load are equal in magnitude and with 120° phase shifts between them.D) None of the above
For the figure below, determine the mesh currents ?1 , ?2 and ?3 .
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Determine the Branch Currents using Kirchhoff’s Laws: a.) Branch bd b.) Branch cd c.) Branch ca
17 In the figure shown, the voltage V1 the voltage V2 by V₁ * out of phase. 40)
A 200 V, 50 Hz, single-phase radial distribution system, the resistance of the wire is 0.0007 ohm/m supply and return. Four loads are connected and it consumes 15, 20, 35 and 45 A respectively and are fed from the cable at distance of 25, 15, 5 and 5 m respectively. Calculate the total current drawn from the supply (I), the current in the cable between each of the loads and the voltage at load A, B, C & D. Total Current, I = Answer for part 1 Branch current between A & B load, Iab = Answer for part 2 Branch current between B & C load, Ibc = Answer for part 3 Branch current between C & D load, Icd = Answer for part 4 Voltage across load A, Va = Answer for part 5 Voltage across load B, Vb = Answer for part 6 Voltage across load C, Vc = Answer for part 7 Voltage across load D, Vd =
A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.05 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 90 KV. Find the Voltage distribution across each unit. Draw the diagram.
12. What is the percentage load to added to a branch circuit conductor having an ampacity equal to or greater than the non-continuous load? a. 75 b. 80 c. 115 d. 125
A 210 V, 50 Hz, single-phase radial distribution system, the resistance of the wire is 0.0007 ohm/m supply and return. Four loads are connected and it consumes 15, 10, 35 and 40 A respectively and are fed from the cable at distance of 15, 5, 5 and 25 m respectively. Calculate the total current drawn from the supply (I), the current in the cable between each of the loads and the voltage at load A, B, C & D. Total Current, | = Branch current between A & B load, lab = Branch current between B & C load, Ibc = %3D Branch current between C & D load, Icd = Voltage across load A, Va = Voltage across load B, Vb = Voltage across load C, Vc = %3D Voltage across load D, Vd =
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Problem 1- Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: A. B Zs (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (13) through impedance Z4. 220V;50HZ Figure 1 Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar Take voltage as reference. notation.
If T = 0.62 – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: a. The first voltage minimum is at 2cm from the load. b. The first voltage minimum is at 8cm from the load. c. The first voltage minimum is at 72cm from the load. d. The first voltage minimum is at 20cm from the load. e. The first voltage minimum is at 24cm from the load. f. The first voltage minimum is at -4cm from the load. g. The first voltage minimum is at 32cm from the load. h. The first voltage minimum is