When the neutral wire in a 3- phase, 4- wire system is disconnected, then: Select one: O a. None of these O b. No remarkable change in the service Oc the service is completely interrupted Od. the loads which are connected between any two line conductors and the neutral are get connected in series and the potential difference across the combined load becomes equal to the line voltage.

When the neutral wire in a 3- phase, 4- wire system is disconnected, then: Select one: O a. None of these O b. No remarkable change in the service Oc the service is completely interrupted Od. the loads which are connected between any two line conductors and the neutral are get connected in series and the potential difference across the combined load becomes equal to the line voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Please answer with detail and how it is done. Photo is attached with the questions.
Q1/ Answer by True or False and correct the false sentence: 1- Wire.begin() is used to initiate the wire library in the slave board. 2- In I2C, the clock frequency in range of 50000 to 300000 Hz. 3- Common Ground means the grounds of each board should be connected with each other 4- Pins 0 and 1 are used for external interruption. Solve all please 5- Interruption mode (rising) means: wherever the pin is low. 6- The function getkey () is used to read the size of the array. 7- The segment display is connected only by a common cathode. 8- Delay functions can be used in external interruption. 9- Pin VCC is used to control the LCD display contrast. 10- Serial functions are used with I2C communication.
1.a. A fiber optic cable has a minimum bend radius of 8 cm and will be mounted in an expansion loop with support messengers. How far should neighboring support messengers be placed when installing this cable?A. At least 16 cmB. Less than 16 cmC. At least 20 cmD. Exactly 20 cm 1.b. A corner pull box has conduits that are separated by 36 cm. If you install a cable in this pull box, what should the minimum bend radius be?A. At least 8 cmB. Less than 12 cmC. Less than 8 cmD. At least 12 cm
Hello, I am having trouble with this homework problem. What would the approach to solve this problem? 1. Show the following units in scientific notation.e.g ) Five Kilometre (km) = 5 x 103 m 1) One Milliampere (mA)_______ x ______ (A) 2) Three Megajoules (MJ)_______ x ______ (J) 3) Six Microcoulombs (µC)_______ x _______ (C) 4) Eight Nanoseconds (ns)_______ x ________ (s)
A pvc raceway has multiple circuits installed. The circuit sizes are 20 amp 60 amp and 100 am. A single copper equipment grounding conductor is to be installed. What size equipment grounding conductor is required to be installed in the pvc?
Please send the answer by typing only. I don't want handwritten. The subject is ( Electronic Circuits ) Q2) Mention the applications of FET.
image
A one-family dwelling has a 175-ampere, 240-volt service that is fed with 75⁰ C (167 degrees) conductors. What is the minimum size copper grounding electrode conductor required ?
A circuit consisting of a filter and an op-amp is shown in the figure below (fig. 7). If R1 = 5 ohms, C1 = 4 farads and if the frequency of the input voltage is 1 rads/sec, calculate the voltage gain of the circuit in dBs (decibels). Insert only the numerical part of your answer without the units. R1 Vin C1 Vout Fig. 7
I need to answer of this question
The answer is not in the choices meaning wrong. Please resolve!