2. A DC distributor cable AB is fed at its ends A and B. Loads of 48A, 72A, 24A and 12A are taken from the cable at points C, D, E and F. The resistance of sections AC, CD, DE, EF and FB of the cables are 8, 6,4,10 and 5 m2 respectively (for the go and return conductors together). The voltage at points A & F is 240V. Estimate: i. the voltages at the feeding point B, the current supplied by each feeder ii. the potential differences at the loads C,D and E.

2. A DC distributor cable AB is fed at its ends A and B. Loads of 48A, 72A, 24A and 12A are taken from the cable at points C, D, E and F. The resistance of sections AC, CD, DE, EF and FB of the cables are 8, 6,4,10 and 5 m2 respectively (for the go and return conductors together). The voltage at points A & F is 240V. Estimate: i. the voltages at the feeding point B, the current supplied by each feeder ii. the potential differences at the loads C,D and E.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Over sting of 3- phase transmission line has 4 insulators and Ce=0.15C. If the voltage between the steel pin of the first insulator and the conductor is 25 kV. Find 1- The voltage distribution over the sting and what will be the string efficiency. 2- If the string is supplied by a guard ring and this lead to add one air capacitance of 0.12C. find the new voltage distribution and the efficiency
The 240 kV transmission line is intended to be connected to a 220 kV transmission system through an autotransformer. The single-phase transformer that is available to make the connection is 120 MVA and 240kV/20kV Draw the connection of this autotransformer and show on the same diagram: The magnitude of the input and output voltages of the autotransformer (Magnitude and polarity)Currents and in the windings (magnitude and direction)The voltages in the windings (magnitude and polarity)The input and output currents of the autotransformer (magnitude and direction)Calculate the power capacity of this autotransformer
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
What size primary conductor can be used for a three-phase, 480V transformer, where the primary overcurrent protection is sized at 110A? Oa.6 AWG Ob.4 AWG Oc.3 AWG Od.2 AWG
a.Why does power plants have high amounts of voltages? Explain. b.Is it safe for transmission lines to have high current instead of high voltage? Why? c.What phenomenon is avoided by having separations between three conductor phases? Explain this phenomenon.
Problem 3.5: From a 3-phase, 480 V generator switchboard, a feeder takes 3-phase power to two equipment at the other end via cable and trans- former with the combined series impedance Z = 0.04 + j 0.09 N per phase. The voltage at receiving end point A rises and falls as a large 3-phase, 500 kVA load at point A varies over time. The small 1 kVA load, also connected at point A, remains online continuously, and must accommodate the voltage variations at point A with the 500 kVA load fully on or fully off. Determine the voltage range that the 1 kVA load will see, over which it must perform within its specifications.
23 kohm 18 kohm V. 4.8 V1 kohm 0.!2 kohm Please BE AWARE that there are multiple variable sheets Please use the variable sheet uploaded And calculate the cutoff frequency. Please give the answer in Hz and do not include anything else than the answer and the format will be in the scientific notation with 2 decimals (ex 5.01e+6 or 1.02e-4).
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
What size primary conductor can be used for a three-phase, 480V transformer, where the primary overcurrent protection is sized at 50A? Oa.6 AWG Ob.4 AWG Oc. 2 AWG Od.1 AWG
According to OES4, The Voltage Drop Tolerance limit for 3 Phase 4 Wire System with power circuit is----- a. 9.60V b. 7.20V c. 12.45V d. 16.60V
In a 3-phase Overhead System, each line is suspended by a string of 3 Insulators. The voltage across the top unit and middle unit are 10KV and 11KV respectively. Calculate (i) Ratio of Shunt Capacitance to Self-Capacitance of each insulator and (ii) String Efficiency