A 2.00-kg block is pushed against a spring with negligible mass and force constant compressing it 0.220 m. When the block is released, it moves along a frictionless, horizontal surface and then up a frictionless incline with slope 370. How far does the block travel up the incline before starting to slide back down? A. 1.16 m k = 400 Njm = 2.00 kg wwwA В. 0.82 m 37.0 С. 3.1 m K-0.20 mH D. 1.2 m Е. 2 m

A 2.00-kg block is pushed against a spring with negligible mass and force constant compressing it 0.220 m. When the block is released, it moves along a frictionless, horizontal surface and then up a frictionless incline with slope 370. How far does the block travel up the incline before starting to slide back down? A. 1.16 m k = 400 Njm = 2.00 kg wwwA В. 0.82 m 37.0 С. 3.1 m K-0.20 mH D. 1.2 m Е. 2 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.81P: Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center...

See similar textbooks

Similar questions

Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
m = 40 kg 4) Determine the magnitude and direction of the friction force which the vertical wall exerts on the 40 kg block if (a) 0 = 15° and (b) 0 = 30°. P= 500 N Hs = 0.50 Hp = 0.40
A 250 lb refrigerator is being pushed. You do not know what force P should be applied. The coefficient of static friction between the refrigerator and floor is point G. 0.4. The center of gravity of the refrigerator is at = d2 ++ d2 → F1 d3 d1 d4 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 4.5 ft d2 1.5 ft d3 2.5 da 3.5 a. Determine the force P that is needed to overcome friction. b. Determine the location of the normal force x measured from the center of the refrigerator if the force P from part a is applied. c. Determine the minimum force P that is required to tip the refrigerator. d. Will the refrigerator slip or tip first? Round your final answers to 3 significant digits/figures.
F m1, m2 two blocks connected by a spring.png Two blocks are connected by an ideal spring on a frictionless floor as shown above. Force F is applied to the block with mass m2. If k is the spring constant, x=|L-Lol is the amount of the stretch/compression of the spring, and g is the free fall acceleration, what is a correct equation for the magnitude of the net force acting on block m2? Check all what applies. m1 F(1 - :) mi+m2 O F-m2a m2 F(1 mi+m2 O (m1+m2)a F-kx
A horizontal force F pushes a block mass m=4kg against a vertical wall. If the coefficient of friction between the block and the wall is 0.2, what is the value of F necessary to keep the block from slipping down the wall. (g= 9.8m/s?) F m
A 60 kgm body has a potential energy if 135 Kcal with respect to a datum plane X and a potential energy of 99 Kcal with respect to a datum planebY. If the local acceleration of gravity is standard, compute the relative position of the plane X relative to plane Y. Reaolve the problem if g=30 fps^2.
AI kg mass is rests on a frictionless I meter long ramp and compresses a k = 4000 N/m spring a distance of 5 cm. The ramps angle of incline varies from 10 to 50 degrees, in increments of 10 degrees. For each angle of incline, determine if the block will slide off the top end of the ramp after it is released from the Spring. Output each angle of incline and whether of not the block reaches the top of the ramp.
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.
Consider the following diagram. m1320 kg and m2= 10 kg. The system is being pulled by an applied force of 200 N, directed 50 above the horizontal. The coefficient of kinetic friction between the block and the surface is u=0.2. 500 20kg m, 10 kg Coeficent of friction 4= 0.2 30 7) Calculate the acceleration of the system. * Your answer 8) Calculate the magnitude of the Tension on the rope. Your answer
In order to burgle a local McDonald's, the Hamburglar must climb onto the roof. To do this, a ladder of length 3.31 m and mass 21.2 kg is placed leaning against a vertical wall, as shown in the image below. There is negligible friction between the ladder and the wall, but the same is not true for the ladder and the ground: us ≠ 0 between those two surfaces. Even with that friction, the ladder will start slipping if the angle ø ladder makes relative to the ground is less than 71.0°. Assuming the ladder is uniform (so that its center of gravity is located at its geometric center), what must be the maximum static frictional force (in N) that exists between the bottom of the ladder and the ground? Explain how you solved the problem involving a ladder leaning against a wall. Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
1:E1 A docs.google.com/for Untitled Section Determine the force P required to lower the 40-kg cylinder at a slow steady speed. The coefficient or friction between the cord and its supporting surface is 0.30. (g-10 m/s³). 40 kg Your answer If (4, =0.4) then the o between the normal force N and the friction force F will be Your answer العربية الإنجليزية III
A spring scale indicates a tension Tin the right hand cable of the pulley system shown in Neglecting the mass of the pulleys and ignoring friction between the cable and pulley the mass m is T. T. Spring scale TA 12T m (a) 27lg (c) 4T/g (b) T(1 + eAT)/g (d) None of these