960 mm 640 N 3 280 mm 360 N a. Determine the tension in segment AC b. Determine the tension in segment BC.

Q: A 100 N 4 60° 3 B 120 N wo cables AC ana BC are attached to the wall. The cables meet at C where two…

A:

Q: For the frame loaded shown, determine the horizontal and vertical components of the pin pressure at…

A: Take moment about D for the whole structure:∑ MD=0RAV4+2002-3002+4=0RAV=14004RAV=350units

Q: . Draw the internal torque diagram of the shaft. 600 N•m 200 N m 200 N m 200 N m A В C D

A: Draw the internal torque diagram.

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A: The torsion on the rigid supports and the maximum shearing stress developed in each segment for the…

Q: A horizontal circular plate weighing 62 lb is suspended as shown from three wires that are attached…

A: Given Weight of plate: 62lb

Q: 40KN/m 210kN E B D 8m 8m 4m 4m

A: For analyzing the above given beam we will be using 3-moment theorem. In this first we have to…

Q: Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and…

A: Given:- b = 260 mm d = 420 mm fc' = 21 MPa fy = 275 MPa To find:- As and n

Q: E D 4 m B -3 m 2m-2 m

A: Hello dear, The answer is found to be P=248.571 KN For explanation please see the attached solution,…

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 13. 12 5 A -x…

A: Given, F= 650 N To determine, Component of projection of force F along OA

Q: P FBD F compute horizontal and vertical displacement at C using a) differential equation. b…

A:

Q: 2.5 KN 7 ΚΝ 15 KN/m 30° A B 2m 4m Im Figure A1/ Rajah A1

A:

Q: If F=80 N, determine the magnitude and coordinate diretion angles of the couple moment. The pipe…

A: Given dataF=80 NFINDdetermine the magnitude and coordinate diretion angles of the couple moment

Q: Find the Beam Design Moment Strength. 250 - 19.5 30 100 20 100 100 50 50 46 -75- -40 311512.7 29.8…

A: Given data:- Characteristic strength of concrete, f'c = 55 MPa Yield strength of steel bar, fy = 400…

Q: draw sf and bending diagram

A:

Q: Resolve each force acting on the gusset plate intoits x and y components, and express each force as…

A: Consider F1

Q: 250' Draw the triangle of for ces 120 and determine the resultant of the two A forces acting in the…

A: Two forces 250N , and 120N and angle between the force 240N and x-axis is 30°

Q: Draw the V&M diagrams. Is this beam at static equilibrium? Calculate the stress due to bending at…

A:

Q: 1. Determine the force in bars BD, CD, and DE of the nacelle truss shown in the figure below by…

A:

Q: D 3rd. G H ZK K. L M P. 1.St. そ20 そとo-30 つ!

A: Assumption  Point of contraflexure occur at the middle points of the members.

Q: 150 lb 300 lb D E A B 24 in.- 4 in. 6 in.

A: Let,RD=vertical reaction at DRE=vertical reaction at…

Q: PROBLEM 1 Two rigid bars AB and DC are supported by four steel (E = 29 x 106 psi) cables as shown.…

A:

Q: EXTERNALLY INDETERMINATE TRUS 25KN 4m B 15KN 4m A D

A: Given externally indeterminate truss which means that all reactions cant be known by summation of…

Q: draw the deflected structure for this frame. note D is a hinge support, E is fixed and C is a roller

A:

Q: 50KN 2m, B 1 5m C AG 5m 5m

A:

Q: *15-8. If the bearing pads at A and B support only vertical forces, determine the greatest magnitude…

A:

Q: SITUATION II I. Refer to Figure sSE - 0001. The combination section shown consists of a wide flange…

A:

Q: The forces F1, F2 and F3, all of which act on point A of the bracket, are specified in three…

A: To find the x and y component of force F1

Q: F 650 N F = 500 N

A:

Q: www. WE A helical spring is fabricated by wrapping wire 3/4 in. in diameter around a forming…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the distance y̅ to the center of gravity of the homogeneous rod.

A: Given: Height of the cable = 2 m Width = 1 m.

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 8 13. 12 5 A…

A: Given :

Q: Determine the shear stress at section b-b.

A: Take moment about A :∑ MC=0FABsin604ft-15042=0FAB=346.41kips

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A: Given data,  Total torque = 750 N-m Diameter of AB = 12 mm Diameter of BC and CD = 25 mm   To find…

Q: The cross-section of member AB is a 0.45in by 0.45in square. Determine the shear stress at section…

A:

Q: P FBD F compute horizontal and vertical displacement at C using. a) differential equation. b/…

A:

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1)…

A:

Q: 5 @ 3m=15m- C H J K L -4 @4m=16m- A B D E 60 kips WHAT IS VERTICAL COMPONENT OF REACTION FORCE AT…

A:

Q: using method of sections. Determine the forces in members BC, BG, and FG.

A:

Q: 03 A force F of magnitude 40 N is applied to the gear. Determine the moment of F about point O. 20…

A: Given data, Force applied to the gear,F = 40N θ= 20° r = 100m

Q: The 9.8-lb force is applied at point A of the crank assembly. Determine the moment of this force…

A: Formulae of Expression for Force & position vector: Expression for force vector:…

Q: de 2.F6 A container of mass m = 120 kg is supported by three cables as shown. Draw the free-body…

A: Given information.The mass of the contGiven information.The mass of the container (m) is 120 kg.The…

Q: Determine the magnitude of the gripping forces exerted along line aa on the nut when two 52-lb…

A: P=52lb To find force exerted along aa

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.