PROBLEM 1 Two rigid bars AB and DC are supported by four steel (E = 29 x 106 psi) cables as shown. The cross-sectional area of the cables are 0.025in?. Calculate the vertical displacement of point I. E F G 3 ft 5 ft H D -1 ft- -2 ft 1.8 ft В 3 ft- -1 ft- 500 lb

PROBLEM 1 Two rigid bars AB and DC are supported by four steel (E = 29 x 106 psi) cables as shown. The cross-sectional area of the cables are 0.025in?. Calculate the vertical displacement of point I. E F G 3 ft 5 ft H D -1 ft- -2 ft 1.8 ft В 3 ft- -1 ft- 500 lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This problem is about replacing the loading system acting on the beam shown below by a resultant force and a couple moment at acting at Point O. Oppfz 350 lb-ft 50pff ∙100th £40016 Determine: a) The resultant couple moment (MRO). Provide the direction of rotation (CW or CCW). b) The component of the resultant force in the x-direction (FRx). Provide the direction of the force. c) The component of the resultant force in the y-direction (FRY). Provide the direction of the force.
Draw the FDBS of member ADB and BEC 1 m 1 m В C E 1 m D 1.6 m
5.1.20 The truss shown in the figure con- sists of-4 bays of 'K' structure. Each bay has 2 m long horizontal and two 2 m long vertical bars. Find the tensions in rods DE and DG. D G J M B E H K F NO 2KN 2KN 2 KN Filenamepllignre5-1-truu7 Problem 5.1.20
Determine the force in member ( EB )of the roof truss shown in fig 3000 loo0 N lo00N f. wode 30 oa bsw m A 2 m 2m 2m 2m Obuing
Situation 8: Light grade steel channels are used as purlins as shown in the figure. The top chords ofthe truss are inclined at 1V:4H. The trusses are spaced at 6m on center. The purlins are spaced at 6m on center. The purlins are spaced at 1.20m on centers. The roof are as follows: Dead load including roof materials 720MPA 1,000MPA 1,440MPA Live load Wind load Wind pressure coefficient Windward Leeward 0.20 0.60 Channel properties Section modulus, S Section modulus, S Weight 6.19x10*mm 1.38x10*mm %3D 79/m The allowable bending stresses are Ex = 207MPA and E = 207MPA. Assume that all the loads pass through the centroid of the channels. 1.20 1.20 EEÉËÈEE Sagrod 21. Which of the following mostnearly gives the maximum bending stress, fex, for the dead and live load combination (DL+LL)? a. 127.11MPA c. 132.20MP. b. 151.14MPa d. 169.48MPA 22. Which ofthe following most nearly gives the maximum bending stress, f, for the dead and live load combination (DL+LL)? а. 169.48MPа c. 127.11MPA d.…
pdf - Adobe Acrobat Reader DC (32-bit) in Window Help Timothy A_Philpot. Bending stress H.W. x C 다 1 /2 111% b, H.W 1 A beam is subjected to equal bending moments of M, = 45 kip ft, as shown in Figure 1a. sions (Figure1b) 6.0 in., bz = 3.0 in., and dz = 2.0 in. Determine The cross-sectional dimen- are b1 = 7.5 in., d = 1.5 in., b2 = 0.75 in., d, = K (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. State whether the normal stress at H is tension or compression. (c) the bending stress at point K. State whether the normal stress at K is tension or compression. M. d b, M. d (d) the maximum bending stress produced in the cross section. State whether the stress is tension or compression. FIGURE 1. a FIGURE 1.6 H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of the shape are shown in Figure 2 b. determine: The Consider the entire 24-ft…
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
Determine the tensions in cables AB, AC, and AD. B Answers: TAB = TAC = TAD = i 2.2 m i i AC 1.75 m CA 185 kg D 2.25 m 1.50 m 0.50 m Z Z Z N N N
Draw the shear diagram for the beam. Click on "add discontinuity" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. +O No elements selected 1 kip/ft V (kip) 5 4 3 2 1 0 in bo & Ń -2 0 5 15 ft 10 2 kip/ft 15 z (ft)
Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm
7:47 59.0 :4G+ KB/S il ul 88 bartleby.com/solution- 14 = bartleby Q&A A 8 Engineering / Mechanical Engineeri... / Inte... / De... Determine the forces in memb... Textbook Problem Determine the forces in members AC and AD of the truss. D 4 kips 12 ft F 8 ft C. 4 ft B 10 ft -5 ft- Want to see the full answer
Sample Problem 5: Compute the forces in members CD and JK, given that P = 3000 lb and Q = 1000 lb. (Hint: Use the section indicated by the dashed line.) Q a Q A B 12-7--|--2₁1--1₁ E! -2 ft- F H 3 ft 3 ft 3 ft