0.20 + j0.50 /km. The load at the receiving end absorbs 10 MVA at 33 kV.9.29 A three-phase, 34.5-kV, 60-Hz, 40-km transmission line has a series impedancez = 0.20 + j0.500/km. The load at the receiving end absorbs 10 MVA at 29Calculate the following:%3Da. ABCD parametersb. Sending-end voltage at a power factor of 0.9 laggingc. Sending-end voltage at a power factor of 0.9 leading

In this question , short 3 phase transmission line is given....We have to find out ABCD parameter…

9.29 A three-phase, 34.5-kV, 60-Hz, 40-km transmission line has a series impedance a 0.20 + j0.50 N/km. The load at the receiving end absorbs 10 MVA at 22 Calculate the following: Z = a. ABCD parameters b. Sending-end voltage at a power factor of 0.9 lagging c. Sending-end voltage at a power factor of 0.9 leading

9.29 A three-phase, 34.5-kV, 60-Hz, 40-km transmission line has a series impedance a 0.20 + j0.50 N/km. The load at the receiving end absorbs 10 MVA at 22 Calculate the following: Z = a. ABCD parameters b. Sending-end voltage at a power factor of 0.9 lagging c. Sending-end voltage at a power factor of 0.9 leading

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.10MCQ: Transmission line conductance is usually neglected in power system studies. True False

See similar textbooks

Similar questions

1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)
30) In a lightly loaded long distance EHV lines, line loading is and has a power factor: (A) Capacitive, lagging. (B) Capacitive, leading (C) Inductive, lagging (D) Inductive, leading. please contact me in whatsapp +962782974574
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
i. Some reasons for adopting high transmission line voltages are to improve ------and the enhancement of. ii. The per phase power transmitted under surge impedance loading of a transmission line is given by: iii. Power transmission lines are limited in their power handling capability by the and
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
Consider the following statements: Surge impedance loading of a transmission line can be increased by 1. increasing its voltage level 2. addition of lumped inductance in parallel 3. addition of lumped capacitance in series 4. reducing the length of the line Which of these statements are correct? (a) 1 and 3 (b) 1 and 4 (c) 2 and 4 (d) 3 and 4
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A 3-phase, 132 kV, 50 Hz, and 200 km line has a resistance of 0.0765 ohm per km per phase, inductance of 0.605 mH per km per phase, and shunt admittance is 4.79 nF per km per phase. It delivers 40 MVA at 0.8 power factor lagging. Find the voltage regulation and transmission efficiency. Use nominal n circuit. --------
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination
A 3 phase, 50 HZ, transmission line represented by TI-model and having the following parameters, A= 0.95L 1° and B = 100L 80°. The line supplies a full load of 80 MW at 220 KV and 0.8 lagging power factor. Determine the following (w a. The elements of the tra. ssion line matrix C and D. b. The values of the line parameters R, L, Rsh and Csh- c. The sending end complex power and power factor. d. The voltage regulation. e. The equivalent transmission line matrix if another line with parameters Z = 7+j70 O/phase and Y = j0.00 S/nhase is connected in parallel with the existing line. h 4 decimal places):
1.The voltage magnitude and phase angle are the quantities to be determined after load flow analysis for............. bus. 2.The total reactance of the transmission system is reduced by installing a series capacitor. Select one: True False
A 3-phase overhead transmission line delivers a load of 80 MW at0.8 p.f. lagging and 220 kV between the lines. Its total seriesimpedance per phase and total shunt admittance per phase are 200ohms with an angle of 80 degrees and 0.0013 mho with an angle of90 degrees per phase respectively. Using nominal-T method,determine the following:(i) A, B, C, D constants of the line(ii) Sending end voltage(iii) Sending end current(iv) Sending end power factor(v) Transmission efficiency of the line