i. Some reasons for adopting high transmission line voltages are to improve -------and the enhancement of ii. The per phase power transmitted under surge impedance loading of a transmission line is given by: iii. Power transmission lines are limited in their power handling capability by the ---- -- and

i. Some reasons for adopting high transmission line voltages are to improve -------and the enhancement of ii. The per phase power transmitted under surge impedance loading of a transmission line is given by: iii. Power transmission lines are limited in their power handling capability by the ---- -- and

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.30P

See similar textbooks

Similar questions

Considering two parallel three-phase circuits that are close together, when calculating the equivalent series-impedance and shunt-admittance matrices, mutual inductive and capacitive couplings between the two circuits can be neglected. True False
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
The equivalent circuit of a single phase short transmission line is shown in Figure Q4 (b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4 (b) for the lagging power factor at load point (Vn). ii) Summarize, the impact of voltage regulation and efficiency, if the line resistance and line increases are doubled Figure Q4(b). R XL Vs Vn Figure Q4(b) Load
iv. For a long high voltage transmission line with light loading : (a) The voltage is generally high due to reactive power generated by the line. (b) The voltage is generally high due to the light loading. (c) The voltage is generally high due to high reactive power generated and the low reactive power consumed by the line.
1.The voltage magnitude and phase angle are the quantities to be determined after load flow analysis for............. bus. 2.The total reactance of the transmission system is reduced by installing a series capacitor. Select one: True False
Outline the drawbacks and the advantages of six-and twelve phase transmission lines configarations.
I) Determining the voltage amplitude and angle values of each busbar II) To determine the active and reactive power values flowing from each transmission line III) To determine the active and reactive power loss values in each transmission line IV). Determining the total active and reactive power loss values in transmission lines in the power system V) To determine the power system temporary stability limit values To explain the reasons for load flow in power systems given above, which option is the correct one of the 5 explanations given? A) II,III,IV B) I,II C) I,II,III D) I,IV E) I,II,IV
PROBLEM 1: a. Find the Real Power, Reactive Power and power factor characteristics of the load. b. Show the real and reactive power flow on each line, complete and separate, THREE-PHASE. Indicate the efficiency of line 2. c. Find the load node regulation. Assume the generator terminal voltage is kept constant.
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
In the medium-length power transmission line model given below, since the end-of-line voltage value of the nominal-T equivalent circuit is 154 kv, find the voltage regulation value for this line and draw the phasor diagram.
The fault current level of a circuit breaker used in a transmission line with phase voltage 4.6 kV and breaking capacity 40 MVA is ...kA. ... ...
A 60-Hz, 230-mile, three-phase overhead transmission line has a series impedance z = 0.8431279.04° 0/mi and a shunt admittance y = 5.105 x 10-6290° S/mi. The load at the receiving end is 174 MW at unity power factor and at 215 kV. Using per-unit calculations, determine the sending-end line-to-line voltage (in kV) and line current (in A). (Enter the magnitudes. Use a base of 174 MVA and 215 kV.) voltage 154.2 current x kv A