(8 – x) . 5 in. Dy -2 in.

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: 12-x2 了了少 Je

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Draw chalk diagram of all sections

A: To draw section views

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: A mass of 25 lb is applied at the end of a 2-inch-diameter rod shown in Figure P2. If the modulus of…

A:

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: ## Moment of Inertia Calculations (by hand)**Given:*** a = 22 ft* y = x^2 (for part a)* y = x (for…

Q: Compute Îx (I bar sub x, in inches“, round-off to 2 decimal places) for the region shown. 6 in. 6…

A:

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: A 5 ft DU B 5 ft -3 ft-

A:

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: 15 What is the weight of the weldment shown? (MS) Plate= .2835 lbs. per cubic inch. V 58" x 21 x 21"…

A:

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: Does this machine maximize or minimize the force (100 lb)* 100ib 20m. 45 15 in. 05in. 100lb

A: Given: Plier with dimensions and forces To find: The effect on force requirement

Q: 1.25 m y 180 N '0.5 m F2 0.75 m

A: In the scalar method, the moment can be calculated as follows: In the cross-product approach, the…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: Which is greater in measurement A. Radius B. Diameter C. Chord D. Both b and C

A: Given that,  For a circle , there is a diameter , chord and radius.

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

A:

Q: Calculate the volume (in ft) of material used in making 350 ft of 2 in. type L copper tubing.

A: Given that, From the table of type L copper tubeFor a 2 in. in nominal size tube:Outside diameter,…

Q: 12 ft 5 kips Koo. 3 ft

A: Given data:-   To find:- the moment at the fixed support A

Q: What is a Couple Moment?

A:

Q: An cylinder has a volume of 38.5 cu.in. and clearance of 2.5 cu.in. Calculate the stroke, if the…

A: Given data:

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.