Solidworks **Build the following part. Report the volume in in³. Assume all dimensions are in inches.**- A = 3.55- B = 2.25**Description and Explanation of the Drawing:**The image shows an engineering drawing of a part with various views, including a top view, an isometric view, and a sectional view labeled as Section A-A.1. **Top View:** - The width of the part is labeled as B. - There are four countersunk holes for 3/8 flat head machine screws, indicated by the note “4X CSK 3/8 FLAT HEAD MACHINE SCREW (100).” - The holes have a diameter of .397 through all, with a countersink diameter of .762 at 100°.2. **Isometric View:** - This view provides a 3D perspective of the part, showing its overall shape and form. - The part has a rectangular base with four holes and a curved section.3. **Front and Section A-A View:** - The front view illustrates the part’s rounded bottom with a radius of R2.250 and a cut-out section. - The sectional view A-A gives a detailed look into the internal cut-out of the part. - The cut-out has a width dimension of A, a depth of 1.500, and a width of 1.350. - The section view shows a depth of .650 for the extension, with the thickness of the walls being .325 typical.These detailed dimensions and instructions are used to calculate the volume and create the part precisely according to the specifications provided in the drawing.

Answered: Image /qna-images/answer/ae923c1f-6b07-43a1-98da-db939736accf.jpg

Answered: Build the following part. Report the…

Engineering

Mechanical Engineering

Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B = 2.25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are some of the operations required of sand castings after removal from the mold
None
Grey cast iron, which contains between 2.5 and 4% carbon, has all or most of its carbon is uncombined in forms graphite flakes when it cools and solidifies from its molten state. True or false.
10 In permanent mold casting process, the steel alloys are casted in ________. a. Brass b. Refractory material. c. Aluminum d. Copper
10. What is Centrifugal casting?
QUESTION 14 Pieces thicker than 5.45mm are considered sheet. O True O False QUESTION 15 In sand casting, natural sands are less economical than synthetic sands. O True O False QUESTION 16 Typical sheet-metal thicknesses are between 0.15 mm and 7 mm. O True False
Aluminum shell 10 in. 1 in. Steel core 2.5 in.
For the sand casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and and finally draw the most suitable form mold for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
Baking of sand mold increases its strength. Select one: True False
A helical spring with a mass of 6 kg has a mass of 10 kg attached to its free end. The mass is now pulled down to 40 mm from the equilibrium position and then released. Determine (a) the frequency of the oscilliation if the spring's stiffness is 532 N.m, (b) the angular velocity of the mass, (c) the instantaneous linear velocity and (d) the kinetic energy of the 10-kg mass when it is 30 mm from the equilibrium position.
Which among the following design considerations for casting to be followed to reduce stress concentration in parts? O a. Shape the casting for orderly solidification O b. Avoid abrupt changes in cross section Oc Avoid thin sections O d. Make provision for easy removal of pattern from the mould
Briefly explain the Centrifugal casting technique with a neat diagram? (minimum 1 page write up)