Answered: 6. Value of Young's modulus of…

6. Value of Young's modulus of elasticity of steel if , Bulk modulus is 160 GPa and Poisson's ratio is 0.29 200 GPa 201.6 Gpa O 758.4 Gpa O 478.6 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
S=25
steel bar originally 200 mm long is pulled in tension with stress 150 MPa the magnitude of elastic modulus E IS 250 GPa, the magnitude of elongation is * O 0.3 mm O 0.6 mm O 1.2 mm O 0.75 mm
A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 8 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage - d D E H b Answer: P= i N
E1= 7 GPA E2= 10 GPA P= 7000 kN V = 40 kN
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
I need to solve the question of strength materials
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.