Steel design, i need a complete solutions thank u..For built up shape shown in figure a) determine the elastic section modulus and b) plastic section modulus and the plastic moment mp, Bending is about x-axis and the steel is A36, FY=248Given: 25.412.7305203 Problem No. 1(b) theFor the built-up shape shown, determine (a) the elastic section modulus and the yield moment andplastic section modulus nd the plastic moment Mp. Bending is about the x-axis, and the steel is A36. Fy = 248 MPa30520312.725.4

Problem No. 1 (b) the For the built-up shape shown, determine (a) the elastic section modulus and the yield moment and plastic section modulus nd the plastic moment Mo. Bending is about the x-axis, and the steel is A36. Fy = 248 MPa 305 203 12.7 25.4

Problem No. 1 (b) the For the built-up shape shown, determine (a) the elastic section modulus and the yield moment and plastic section modulus nd the plastic moment Mo. Bending is about the x-axis, and the steel is A36. Fy = 248 MPa 305 203 12.7 25.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A=5, B=3, C=8 AB=53 BC=38, CB=83 CA=85
4.c
A circular bar of magnesium alloy is 390 mm long. The stress-strain diagram for the material is shown in the figure. 70 63 56 49 O (MPa) 42 35 28 21 14 7 0.002 0.004 0.006 0.008 0.01 The bar is loaded in tension to an elongation of 2.34 mm, and then the load is removed. Hint: Use the concepts illustrated in the figures below. (Assume the curve in the figure above is linear between (0, 0) and (0.001, 28), and curves with a gradually decreasing slope otherwise.) F В E F Loading CD Loading Residual Elastic strain recovery (a) What is the permanent set of the bar (in mm)? 2.184 X mm (b) If the bar is reloaded, what is the proportional limit (in MPa)? 55 X MPa
Question 7
MN=85
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
Give me right solution with clear hand writing.
Determine the maximum shearing stress developed in aluminum. Determine the maximum shearing stress developed in steel. Determine the maximum shearing stress developed in bronze.
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm