6. An L5 X 31/2 X 1/2 angle, as shown in Figure below is to carry 20 kips dead load and 70 kips live load using the shortest length of connection using two gage lines of bolts in the 5 in leg. What is the minimum acceptable stagger, theoretical and specified (1/2 in multiples) using A572 Grade 50 steel 80 k ³4*} Gusset plase Other holes not shown (assume at least three)

6. An L5 X 31/2 X 1/2 angle, as shown in Figure below is to carry 20 kips dead load and 70 kips live load using the shortest length of connection using two gage lines of bolts in the 5 in leg. What is the minimum acceptable stagger, theoretical and specified (1/2 in multiples) using A572 Grade 50 steel 80 k ³4*} Gusset plase Other holes not shown (assume at least three)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

j) what is the bolt shear capacity of the flange connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
What will be minimum number of bolts required in each row for a suitable bolted bracket connection of an ISHT 75 section attached to the flange of a ISBH 300 @ 577 N/m to carry a vertical factored load of 600 kN at an eccentricity of 60 mm as shown in the figure? Take design strength of bolt as 65.19 kN. [Assume pitch P= 60 mm] P O O
Question No.3: Determine the maximum tensile force, Pu, that can be applied to the connection shown in figure below based on the bolt strength; assume ASTM A36 steel for the following bolt types in standard holes: Check every limit state. a. 1-in.-diameter A325N, b. 7/8-in.-diameter A490X. 3" 3" 1½" /" plate ½P, P ½P. /" plate
01:) Determine the design tensile strength for the member and bearing type connections if A325 3/4-in standard bolts are used as shown below, threads are excluded for shear plane (Fy =36ksi and Fu=58ksi). Note: don't consider the slip critical connection in your calculations, E of steel is 29000ksi 13 in 13 in 13 in 13 in | 2 in 3 in 12 in 3 in PL를 x 12 PL 1 x 12 P/2 P/2 E PL x 12
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Question 3 Determine the capacity of plate as well as below connection based on Balts (4) in the below Following reactions :- 7 11 A325, $4 þ Bolts use! Use: AISC manual U Moment = 10 kip-67 2 kip (2) Shear (3) Axial 2 kip رب Ź Plate (A 36) 10 " x 10" x ≤ 11 8 HSS. их их nxuxt 4 H² 7
3.5-3 In the connection shown in Figure P3.5-3, the bolts are 4-inch in diameter, and A36 steel is used for all components. Consider both the tension mem- ber and the gusset plate and compute the following: a. the design block shear strength of the comnection b. the allowable block shear strength of the connection http://www.jamarana.com 12" -34 1/2" www.jan 3/2" t = 3/8 2/2" t = 7/16 FIGURE P3.5-3
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.
Question 12. Determine the net area (An) and effective net area (A) for the channel tension member shown below. Assume bolt diameter is 5/8 in. The section is C6x10.5 (A36) (- 1½" lapttp 4@2" le ole ole ole o o ob O Ос
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
a] Compute LRFD 6.) Compute ASD CIVIL STEEL DESIGN ENGINEERING- BOLTED CONNECTION Sample Problem 5: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when threads are excluded from shear planes. The angle consists of A36 steel. Properties of 4 175 x 100 x 16 A36 Steel Properties of A490 bolts A = 4181 mm² t = 16 mm Fy = 248 MPa F₁ = 400 MPa Fy = 276 MPa Nominal hole dia. = 27 mm 75 T+ 100 Gusset Plate 100 F 100
1. what is the bolt shear capacity of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi