The tank of the air compressor is subjected to an internal pressure of 120 psi. The inner diameter of the tank is 22 in., and the wall thickness is 0.25 in. 01 = Part A Determine the hoop stress acting at point A. Express your answer in kilopounds per square inch to three significant figures. ANSWER: ksi 02 = Σ Tap image to zoom Part B Determine the longitudinal stress acting at point A. Express your answer in kilopounds per square inch to three significant figures. ANSWER: ksi

Determine the shear strain xy at corners A, B, C, D if the plate in Figure 5 distorts as shown by the dashed lines. Consider small strain assumption. 3 mm 300 mm y D 4 mm 400 mm- 12 mm B A mm 8 mm $2 mm X

Please give me right solution a,b and c...

Problem 1: Given is a brass bar assembly as shown in the figure, evaluate the average normal stress that is being developed at points A, B, and C. 1 in. 0.5 in. 0.5 in. B. 3 kip 9 kip | 8 kip ↑ C 2 kip A

B P A y W Find the Vertical Position of the Centroid marked as y on the Diagram using the transform section method, transforming all your material to Material A. Your Answer should be in mm to 1 decimal place. J-22.0 mm, P=76.8 mm, W-187.2mm, Young's Modulus of Material A = 64.5 GPa, Yield Stress of Material A = 145.9 MPa, Young's Modulus of Material B = 94.4 GPa, Yield Stress of Material B = 272.9 MPa.

Problem 5 The load has a weight of 950 lb. -1.5 ft- 1 in. max = Section a - a Q Tap image to zoom Part A Determine the maximum normal stress developed on the cross section of the supporting member at section a-a. Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: ksi

The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi

Determine the state of stress acting at point D. Take P₁ = 50 kN and P2 = 10 kN. OD= B ANSWER: P₁ TD= -1.5 m 1.5 m--1.5 m- 0.5 m 40 mm 100 mm 60 mm T D E P₂ 80 mm Part A Find o D. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: C Q Tap image to zoom Part B Find TD- Express your answer to three significant figures and include the appropriate units.

Consider the state of stress shown in 01, 02 = 20 MPa 40 MPa Opi 100 MPa Part A Determine the principal stresses. Enter your answers in megapascals to three significant figures separated by a comma. ANSWER: Q Tap image to zoom MPa Part B Specify the orientation of the principal plane. Express your answer in degrees to three significant figures. ANSWER:

Rods AB and BC have diameters of 2.9 mm and 4.6 mm, respectively. A force F = 2.4 kN is applied to the ring at B, as shown. (Figure 1) Determine the angle so that the average normal stress in each rod is equivalent. Express your answer to three significant figures. What is this stress? Express your answer to three significant figures and include appropriate units.