Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to itsoriginal position, are respectivelyP0.379 m and 45.30 KN0.781 m and 45.30 KN0.651 m and 43.60 KNP = 80KN0.272 m and 43.60 KNQ+Pontoons 15 m² each8 mi8m.w = 9.81 KN/m³EI180000 KN.m²R

Calculate the deflection at Q :ΔQ = PL3 / 3EIwhere:ΔQ is the deflection at QP is the load at Q…

Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to its original position, are respectively 0.379 m and 45.30 KN 0.781 m and 45.30 KN 0.651 m and 43.60 KN P = 80 KN 0.272 m and 43.60 KN 8m Pontoons 15 m² each Q 8m w = 9.81 KN/m³ EI 180000 KN.m²

Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to its original position, are respectively 0.379 m and 45.30 KN 0.781 m and 45.30 KN 0.651 m and 43.60 KN P = 80 KN 0.272 m and 43.60 KN 8m Pontoons 15 m² each Q 8m w = 9.81 KN/m³ EI 180000 KN.m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A bearing plate is to be designed for a W21x62, A36 steel beam that will sit on a reinforced…

A: The steel section used as bearing plate = W2162The yield strength of steel (fy) = 345 MPaThe…

Q: Determine the internal shear force at point C of the beam. Give your answer in N and to 3…

A: Given UVL = 200N/m to 400 N/mSpan 6 mTo find out Shear force at C

Q: The wood beam has an allowable shear stress of Tallow = 4 MPa. (Figure 1) Figure Part A 50 mm 50 mm…

A: Given:Required:Maximum value of shear force

Q: 2K/Ft 두717772년 쬬 * Try K-10' 20 ㅋㅋㅋ *

Q: A composite beam is fabricated by bolting two 3.7-in-wide by 14-in.-deep timber planks to the sides…

A: two 3.7 in wide by 14 deep timber planks to the sides of a 0.7-in. by 14 in steel plateThe moduli of…

Q: Hand

Q: Determine the shear and moment throughout the beam as a function of x. 15 kN/m 4m 2 m

A: The simply supported beam is shown in the above figure. We have to determine the shear and moment…

Q: Hand

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are…

A: Full depth seepage take place. Determine the limiting depth of slope (Hc).

Q: In terms of installing EV charging stations, what should be included in a project schedule?

A: Phase 1: Planning and Site SelectionConduct a feasibility study to assess the need for EV charging…

Q: Calculate the ultimate moment capacity of a rectangular beam with b = 350 mm, d = 540 mm. As = 7x28…

A: The width of the beam is 350 mm.The depth of the beam is 540 mm.The diameter of the bar is 7-28…

Q: Consider the following plot of cumulative arriving and departing vehicles at a freeway bottleneck…

A: The plot of cummulative arriving and departure vehicles is shown below.

Q: Situation A cantilever beam, 3-5 m long, carries a concentrated lo Given: P = 200 kN Beam Modulus of…

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w…

Q: Determine

Q: Determine the internal normal force, shear force, and bending moment in the beam at points C and D.…

Q: Calculate the count of cycles resulting in breakdown. Given Crack length = 0.2 mm Fracture toughness…

Q: Situation 3: A6 m long fix-ended concrete beam has a width of 310 mm and an overall depth of 480 mm.…

A: Width of beam,b=310 mmOverall depth of the beam, D=480 mmSpan, L=6myield strength of steel, fy=415…

Q: Analyze the beam shown below and draw S.F.D and B.M.D. A A E 30 kN-m B x3m 3m² 40KN F с 2 40KN *2mx

Q: Find the value and location of maximum deflection of: T L w。

A: A simply supported beam with uniformly varying load is given, we need to find out the value and…

Q: A W 16 x 50 is used as a beans to carry a uniform we and dead load including own weight of 39.7 kN/m…

A: The allowable axial stress :Allowable axial stress = (Fy * Sx) / (5.0 * (K * L / r)2)where: Fy is…

Q: Situation 1 - For the continuous beam shown in the figure, determine the following: 12 kN/m P = 50…

A: To derive the moment equation for points A and B, we can use the Three-moment theorem,6MA + 2MB + MC…

Q: 3. LIMITATION OF AUTHORITY The Architect as the Construction Manager shall not: 3.1 involve himself…

A: Construction project management is a critical discipline that ensures the successful execution of…

Q: 000 100 250b 250b gniblo pud tadt smuez A Ma The rigid pipe is supported by a pin at A and an A-36…

A: Young's modulus, E=200 GPadiameter of the wire, d =6.5 mmload P= 3 kNTo find:stretch the length

Q: Determine the support reactions at A and D. 1.5 m 1.5 C -1.5 m 4 kN

A: Given:Required:Support reaction at A and D

Q: AD P

Q: 64 kN • m C D 24 kN/m 2 m2 m2 m B S250 × 52 Draw the shear and bending-moment diagrams for the beam…

Q: QUESTION 1 (a) Sketch a bar element, a plane truss element, and a beam element. Label the axes,…

Q: Consider a catchment that has a runoff coefficient of 0.82, an average slope of 0.02, a Manning's n…

Q: AZ B Ф q С

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum…

A: Beam sectionA simply supported beam with two point loads and a uniformly distributed load.To find:…

Q: Can you please explain the equations and theory of finding the location? I am having a hard time…

Q: 1. Estimate the maximum wave heights at points A and B in the region behind the breakwater in the…

A: Estimate the wave height at the breakwater. This can be done using the following equation:Hb = Hi *…

Q: Problem 3 Liquid in a round tank is draining out a round pipe. The term 1) -V() 2) - Vn() 3) -Vπ ()²…

A: dh/dt=??We used here V1 = Velocity at exit = V V2 = Velocity at top of water surface According to…

Q: Determine the reactions at the supports for the structures shown.

A: For the above given figures, we have to find out the reaction at supports.

Q: depth of 600mm and total depth of 650mm. It is reinforced with 4-32mm diameter bars for tension. fc'…

A: Width of the reinforced concrete beam (b): 300 mmEffective depth of the beam (d): 600…

Q: Determine the permissible ultimate moment capacity of a rectangular beam reinforced for tension only…

A: Singly Reinforced Rectangular BeamWidth of beam, b=300 mmEffective depth of beam, d=390…

Q: hat challenges are they when sorting waste to be received

A: Depending on the waste management system in place, local regulations, and the type of waste that…

Q: Given: wet soil sample weight 45.6 lbs volume of soil before drying 0.40 cubic ft dry sample wt.…

Q: PROBLEM: A built up section of A992 steel is made from plates fully welded togethe The flanges…

A: The grade of steel used = A992 steelThe steel section used as a flanges = PL 16x380The steel section…

Q: Can you explain the eqautions and processor for finding the location of the trust on the wall? I am…

Q: A Section 5.4 5.29 through 5.51 Draw the shear and bending moment diagrams and the qualitative…

Q: Problem 15.120 The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with…

Q: Virtual Work Principle

Q: - (+) = + AB 71 KN or 0.672 → (+) √821/ or 35.71 KN (T) =D 1.20 +35.71821 - AC-0 10. 93 км от чаязки…

Q: A cohesive soil is subjected to dynamic compaction. If a 10 metric ton weight is dropped 10 meters…

A: Given data,weight dropped =10metricheight of dropped=10mFINDHow many meters soil feel the effect

Q: How much service live load, in kN/m, can be supported? The member weight is the only dead load. The…

A: Service dead load = 45 kNService live load = 90 kNGross area, Ag = 18400 mm2Radius of gyration, ry =…

Q: The stiff-leg derrick used on ships is supported by a ball- and-socket joint at D and two cables BA…

A: Given:Required:Tension in cables and support reaction at D

Q: Determine the internal normal force at point C of the beam. Give your answer in N and to 3…

A: Given Loading UVL 200 to 400 N/mSpan 6 mTo find out Normal force at C

Q: A 4.2-km² catchment with 0.5% pond area has a curve number of 79, a time of concentration of and a…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to its
original position, are respectively
P
0.379 m and 45.30 KN
0.781 m and 45.30 KN
0.651 m and 43.60 KN
P = 80
KN
0.272 m and 43.60 KN
Q+
Pontoons 15 m² each
8 mi
8m.
w = 9.81 KN/m³
EI
180000 KN.m²
R

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Deflection at Q :

VIEW

Step 2: Calculation:

VIEW

Step 3: Reaction at Q:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to its original position, are respectively P = 80 7 = 9.81 KN/m3 KN EI = 180000 KN.m2 8m 8m. Pontoons 15 m2 each O 0.651 m and 43.60 KN 0.272 m and 43.60 KN O 0.781 m and 45.30 KN 0.379 m and 45.30 KN
Problem 5: (a) Replace the loading acting on the beam by an equivalent resultant force FR and couple moment (MR)B at point C. (b) This time replace the loading on the beam by an equivalent resultant force only (FR =?) and specify where this force acts, measured from C (x' = ? ). (Note: Ignore the depth of the beam) 15 kN 10 kN/m 30 kNm В C D -2.0 m- 2.0 m 2.0 m 1.0 m'
Determine the vertical reaction at E for the beam shown using the slope-deflection method. 20 kN/m 60 kN A E B C D -8 m+4m+4m-| -8 m El = constant E = 70 GPa 1= 800 (106) mm4 O a. 111.2 kN O b. 164.7 kN O c. 78.8 kN O d. 25.3 kN
2:11 ul a 14.0 @ 64 From the figure shown: -15 KN/m 1Om. What the moment at midspan if is 2 m. distane X. if the moment Find the midspan is zero at distance x2 so that the Detersine maximum mo ment in the beam is the least possible value. the 8. A beam ABC with an overhang at one end supports a uniform load of 12 kN/m and a concentrated load of 2.4 kN at the free end at C. w312 kN/m 2.4 kN B 16 m 1.6 m 1.6 m Determine the maximum shear. Determine the maximum moment. 9.
PROBLEM 2 Determine the reaction forces of the hinge at the left end and the roller at the right end if the beam is in equilibrium. jsku/m 50 KN 19 2 m.
(a) Derive the shear force and bending moment equations for the overhang beam. (b) Draw the shear and moment diagrams for the overhang beam. 3 kN 3 kN/m c) 20 kN · m В- 3 m 3 m
Using MDM, what is the reaction at support C? 4 kN 20 kN 18 kN 4 kN/m A C. D 2m 6m 2m 2m 4m 2m Select one: О а. 16.38 kN O b. 8.74 kN C. 10.42 kN d. 13.65
Determine the vertical displacement at point B. Note: Use two (2) decimal places in the final answer. 15 kN 6 kN/m Bll 2EI EI EI 2.0m 4,0m 2.0 m VD 8.0 m 113.50/EI O 153.50/EI O 149.50/EI none of the abovc
10 kN Calculate Moment abou -0.6 m - -0.6 m- 1. Point A 2. Point B A 277 15 KN 60 0.8 m 60° 0.4 m B
Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is supported as shown. Find the following: 300 KN 15 kN/m a. Reaction at A (KN) slim 1.5 kNm b. Reaction at B (kN) B с c. Slope at C in radians 2m 10m d. Displacement at the application of 300kN load m | 3m | 3m t
For the beam loaded as shown in the figure below, determine the following unknowns using any method. a. Moment at A in kN-m. Indicate negative if counterclockwise. b. Moment at Cin kN-m. Indicate negative if counterclockwise. 31.4 kN 35.1 kN/m |B 3 m 3.6 m
В A smooth can C, having a mass of 3 kg, is lifted from Ö=2rad/s² e = 0.5 rad/s r a feed at A to a ramp at B by a rotating rod. If the rod rotates angular velocity of d=0.5 rad/s and %3D =2rad/s?, determine the forces which the rod and 600 mm circular ramp in the vertical plane exert on the can A at the instant 0-30º. Neglect the friction and the size of the can so that r = (1.2cos0) m. The ramp -600 mm- from A to B is circular, having a radius of 600 mm.