50w at to 9 • A Power transistor for which TJmax = 180°c Can dissipa a case temperature of so°c. If it is connected heat sink using an insulating washer for which the thermal resistance is 0.6 °C/W, what heat sink temp. necessary to ensure safe operation at 30w ? For an ambient temp. at 39°c, what meat sink thermal resistance is required? If a praticular aluminum finned heat sink, thermal resistance in still air is 4.5°C /w Per centimeter of length, how long a heat Sink is needed? Ans: Ts = 84°C , OSA = 1.5°C/W; heat sink length is 3 Cm

50w at to 9 • A Power transistor for which TJmax = 180°c Can dissipa a case temperature of so°c. If it is connected heat sink using an insulating washer for which the thermal resistance is 0.6 °C/W, what heat sink temp. necessary to ensure safe operation at 30w ? For an ambient temp. at 39°c, what meat sink thermal resistance is required? If a praticular aluminum finned heat sink, thermal resistance in still air is 4.5°C /w Per centimeter of length, how long a heat Sink is needed? Ans: Ts = 84°C , OSA = 1.5°C/W; heat sink length is 3 Cm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
2. Given:VCC: 16 voltsRB1: 7000 ohmsRB2: 50 ohmsRB3: 50 ohmsRB4: 1500 ohmsB=beta: 100RE: 750 ohmsRC: 500 ohmsVCE: ? volts
1. Given:VS1: -1 voltsVS2: 24 voltsB=beta: 150RE: 330 ohmsRC: 750 ohmsVC: ? volts
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). a) 0.11A b) 22mA to 89mA c) 9A d) 0.11A to 9A
A voltage, 100sin314t volts, is maintained across a circuit consisting of a half-waverectifier in series with a 50 ohm resistor. The resistance of the rectifier may beassumed to be negligible in the forward direction and infinity in the reverse direction.Calculate the average and r.m.s. values of the current.
please give detail explain.. Ans : Rth = 28 ohm Vth = 92 V
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
Q#2 (A) The circuit shown in figure below has a Ves(oft) = -4V. Assume that you increase the supply voltage VoD, beginning at zero until the ammeter reaches a steady value. What does the voltmeter read at this point? Rp 4.7 kn VDp Figure (B) Assume for a particle JFET, Ioss=12mA and Ves(off)= -5V? a. What is lp Wwhen Vas-0V? b. What is lo when Vas=Vas(off)? c. If Vcs is increased from -5V to -2V, does lo increase or decrease?
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (2W10). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.
A single-phase full-wave rectifier, energized from a 220 Vrms, 50 Hz ac source, supplies power to an unknown load. The load current is shown in the figure together with the line voltage. a) Recommend a circuit for the load by examining the current waveform. Draw your circuit in PSIM and obtain same voltage and current waveforms. b) Calculate apparent power, the active power and power factor. Then verify the results using PSIM. A DA LOAD ? 本D。本D Vs[V] Is[A] Vs Is 5A 12ms 18ms t |s] 2ms 8ms -5A